7
English
MANDATORY
INDICATION
INFORMATION
INSTRUCTION
WARNING
PROHIBITION
These signs give advice
concerning your safety
This symbol indicates that the
machine is in conformance with
the applicable European directive.
TYPE
TYPE
SERIAL
POWER
VOLTAGE
FREQUENCY
INTENSITY
FABRICATION
YEAR
WEIGHT
MAXI TOOL
BORE
SPEED
MANUFACTURER
MASSE UTILE
Kg
mm
mm
Ø MAXI OUTIL.
Ø ALESAGE
T/MN - RPM
N° SERIE
ANNEE DE
FABRICATION
PUISSANCE
kW
Hz
V
A
PLAGE DE
TENSION
FREQUENCE
INT. UTIL.
Instruction plate
• Power : 0,8 KW
• Voltage : 230 V - 50 Hz
• Motor speed : 2800 rpm
• Dimensions (mm) l x w x h :
- 425 x 380 x 240
• Weight : 10 kg
• Blade cooling by partial immersion
• Tank capacity: 1,5 litres (autonomy 10 minu-
tes cutting)
• Power cable : HO5 VVF 3 x 0.75 mm
2
- length
1,50 m.
• Use coefficient : 15% (10mn/h)
2
Technical features
6
Starting up
•Disconnect the machine.
•Remove the disk covers (A)and(B).
•Remove the water bath (C).
•Unscrew the tightening nut right-hand
thread(D).
•Remove the outer flange (E). The blade is
tightened by hand, or use a spanner as
appropriate.
•Fit the diamond blade.
• Check correct centring of the blade.
• Replace the outer flange and lock the nut.
• Replace the disk housing
•Check that the disk is centred.
5
Fitting the blade
3
Pre-use check-list
• Utilisation : Water-cooled cutting of tile
materials.
• Blade with continuous rim Ø 180 mm (D)
bore Ø
x
2
5,4
mm (AL).
• Cutting thickness (material) :
to 90° : 34 mm - to 45° : 20 mm
• Cutting width (Lg) with guide at 90° :
170 mm
• Length of cut unlimited.
1
Utilisation
Use only continuous rim diamand
blades.
Before use, read the instructions
carefully and familiarise yourself
with the machine.
The working area must be per-
fectly tidy, well lit and must offer
no risks (no humidity or dange-
rous products in the vicinity).
Always take care.
Get into a comfortable, balanced
position.
Remove all adjustment tools and
wrenches from floor and machi-
ne
Keep the protective covers in
place while the machine is opera-
ting.
Rotation direction is indicated by
an arrow on one side of the
blade.
Make sure the contact faces of
flanges, of blade and the axle are
clean
• Fill the water bath.
• Connect the machine to the mains.
• Start by means of the on-off switch
I
.
The operator must wear
suitable protection when
working.
Any unauthorised persons must
be kept away from the working
area.
Use blades suitable for the work
to be done (speed, geometry,
application, etc.)
- Check the mains voltage is iden-
tical to that shown on the instruc-
tion plate N on the machine
[FIG.
x
1]
- Use twin & earth plugs S.T.D. 3
pin plug 240 V.
- Extension cable : cable section
adequate for the electric power,
connection to the main by a type
HO7 RNF cable of 2.5 mm
2
sec-
tion up to 50 m.
0.8 KW 230 V
74
68
0.08
MODEL
POWER
LEVEL
Lwa (dB)
EN ISO 3744
Lpa (dB)
EN ISO 4871
G
ENV 25349
PRESSURE
LEVEL
VIBRATION
LEVEL
4
Electrical connections
- ELECTRICAL SAFETY :
Operate this machine only on a
supply equipped with a 30 mA ear-
thed current-limiting circuit-brea-
ker. Otherwise, consult our catalo-
gue for appropriate models.
- The RCCB must be used cor-
rectly, including testing it regu-
larly. For tools supplied with an
integral RCCB in the cable or in
the mains plug, if the cable or
plug
has
been
damaged,
repairs must be carried out by
the manufacturer, one of his
agents or by a qualified repair
workshop to avoid any risks
resulting from errors.
