Digitus DN-70590 User Manual Download Page 15

Page: 15 / 170

1-5 Know your new wireless broadband router

Front Panel

LED Name Light

Status

Description

PWR

On Router

switched on and correctly

powered.

2.4G

2.4GHz Wireless WPS function is
enabled.

Off

2.4GHz Wireless network is switched off.

Flashing

2.4GHz Wireless LAN activity
(transferring or receiving data).

5GHz Wireless WPS function is enabled.

Off

5GHz Wireless network is switched off.

Flashing

5GHz Wireless LAN activity (transferring
or receiving data).

LAN 1-4
LNK/ACT

LAN port is connected.

Off

LAN port is not connected.

Flashing LAN

activity

(transferring or receiving

data).

WAN
LNK/ACT

WAN port is connected.

Off

WAN port is not connected.

Flashing

WAN activity (transferring or receiving
data).

LAN 1-4
1000M

LAN port is linked in 1000Mbps speed.

Off

LAN port is linked in 10/100Mbps speed.

WAN
1000M

WAN port is linked in 1000Mbps speed.

Off

WAN port is linked in 10/100Mbps speed.

Summary of Contents for DN-70590











































































































































































Search results

Summary of Contents for DN-70590

Reviews:

Related manuals for DN-70590

Brands by name

Popular brands

Digitus DN-70590, User Manual

Search results

Summary of Contents for DN-70590

Reviews:

Related manuals for DN-70590

Brands by name

Popular brands