manualshive.com logo in svg

Digital Watchdog VMAX IP 16CH, User Manual

Share
Download
Digital Watchdog VMAX IP 16CH User Manual Download Page 65

63 | VMAX IP™ Complete IP System Bundle

 

 

Click the time or move the time bar to the cameras in playback mode. 

The search table displays 24 hours for the selected day. You can couple-click on a selected hour to view a detailed time 
search as seen below. Detailed search is available on a 5-minute basis. 

 

Playback Control Panel: 

 

No. 

Button 

Description 

1

 

 

Go to first data. 

2

 

 

If pressed while in forward playback : Decrease playback speed   
If pressed while in reverse playback: Increase playback speed. 

3 

 

Skip forward. 

4

 

 

Reverse playback. 

5

 

 

Pause.

 

 

6 

 

Forward playback. 

7 

 

Skip backward. 

8 

 

If pressed while in forward playback Increase playback speed   
If pressed while in reverse playback: Decrease playback speed. 

9 

 

Go to last data. 

 

6.4.9 Event Search 

Pivot can receive event data from NVRs that support event notifications to a remote software. See 4

.4.3. Notifications

 for 

more information. The event search has two search options: Event Log and System Log. Event Log display all event 
notifications received from the NVR. The system log will show Pivot start/end, live/search, option, remote setup, image/movie 
export etc. 

 

To run the Event Search: 

Summary of Contents for VMAX IP 16CH


























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands