DIGITAL SYSTEMS ENGINEERING DVE10VR2 User Manual Download Page 8

8

um-dve10vr2 (g)  4/17

PRoDUCT CARE AND MAINTENANCE

DISPLAY ENCLoSURE

•  Clean enclosure with a soft clean cloth lightly dampened with a general purpose mild 

detergent solution

•  wipe down with clean water, and

•  dry with a soft clean cloth.

This dve10vr2 display is designed to provide optimum performance and service without 

any required scheduled maintenance other than occasional cleaning.  prior to use, remove 

the protective film from the display screen.

DISPLAY SCREEN CLEANING

The display screen is a glass-based product. power OFF the unit prior to cleaning.

•  with a slightly damp cloth, lightly wipe down screen to remove dust and grit; always use 

a fresh side of cleaning cloth to avoid scratching

•  Follow with a fresh cloth dampened slightly with cleaner

•  a vinegar-based cleaner is recommended; this prevents streaking and degradation of 

coatings, or use a nonabrasive glass cleaner such as a professional foam glass cleaner

•  wipe left to right or right to left row patterns; swirling is not recommended 

•  To minimize risk of abrasion to display screen, air drying is recommended.

ToUCh SCREEN CLEANING

•  Touch screen (optional): use a special screen cleaning tissue or a solution specifically 

formulated for antistatic coatings. Follow the manufacturer’s instructions, or

•  Lightly dampen a soft clean cloth with water or a general purpose mild detergent solution

•  On screen, always use a fresh side of cleaning cloth to avoid scratching, and

•  To minimize risk of abrasion to display screen, air drying is recommended.

PRoDUCT CARE

uSER TIp

In marine or similar environments, an added benefit of a vinegar-based 

cleaner is its effectiveness in dissolving mineral and salt deposits. 

  

CAuTION! INSTRuCTIONAL

WARNING! ShOCk hAzARDS

disconnect from power source before cleaning screen or enclosure.

•  do not use abrasive cleaners or solvent-based (flammable) cleaners on

    screen, its enclosure or any other electrical connection

•  do not use paper products; they may scratch the screen, and

•  do not directly apply cleaning solutions to screen.

Summary of Contents for DVE10VR2





















Reviews: