Digital Security Controls GS2060 Installation Manual Download

Page: 9 / 53

3. To wire the Communicator to the panel, perform the following (See

Figure 3

a. Disconnect the AC power and the b connections from the panel.

b. Attach a wire from the Communicator’s left

PWR

terminal to the panel’s

BELL+

terminal.

NOTE: For ULC Commercial Fire Monitoring applications, do NOT connect any devices on the Bell+

terminal other than the GS2060/TL260GS.

c. Attach a wire from the Communicator’s

GND

terminal to the panel’s

AUX

terminal.

d. Attach a wire from the Communicator’s

SHLD

terminal to the panel’s

EGND

terminal. (Protective earth

ground).

e. If a Bell/Siren is used, attach a wire from the Communicator’s right

PWR

terminal to the positive (

) termi-

nal on the Bell/Siren. (See

Figure 3

f. If a Bell/Siren is used, attach the panel’s

BELL

terminal to the negative (

) terminal on the Bell/Siren.

NOTE: If a Bell/Siren is not used, install the 1K



½ W 5% resistor (Brown, Black, Red, Gold) (sup-

plied with the panel) between the panel’s Bell + and Bell - terminals, then only wire the BELL + to

the PWR terminal on the Communicator.

g. Confirm that the SIM card is inserted and locked. (See

Inserting and Removing the SIM Card on page 3

h. Insert the PC-LINK connector into the Communicator’s PC-LINK socket. (Black wire on Pin 1 on the

Communicator).

i. Route the CAT 5 Ethernet cable through back of the cabinet and plug it into the Communicator’s RJ45

jack.

NOTE: Before leaving the premises the Ethernet communication lines must first be connected to an

approved (acceptable to local authorities) type NID, (UL installations, UL 60950 listed NID, for ULC

installations CAN/CSA C22.2. No. 60950-1 Certified NID).

4. Perform the following for initial power on of the panel with Communicator installed:

a. Reconnect the AC power and b connector to the panel. (the Communicator and Panel will power

up together).

b. Observe that the Communicator’s red and yellow LEDs are flashing together while it initializes. The red

and yellow LEDs will continue to flash until the unit has successfully communicated to all programmed

receivers. If this is the first time the Communicator has been powered up, the module will request pro-

gramming from Connect24.

c. At the keypad, enter [*][8][Installer Code][382] and confirm that Toggle Option [5] is

(GPRS/Ethernet

Module Enabled).

NOTE: Initialization may take several minutes to complete. Red and yellow LEDs will flash together

during initialization. Do not leave the installation until the red and yellow LEDs have stopped flash-

ing. (If only the yellow LED is flashing, there is a Communicator trouble and the Green LEDs are not

valid for Communicator Placement Test). Correct trouble before continuing. (See Table 6 for trou-

bleshooting assistance).

5. Perform the Communicator Placement Test on page 8.

PC1616/1832/1864 Programming

Perform the following steps to ensure that the Communicator and the panel work together as intended.
These Sections must be programmed at the panel keypad. Enter [*][8][Installer Code][Section Number]. Record

any values that are modified from their default, in the appropriate Worksheets for the Panel or Communicator.

NOTE: The toggle is ON when the number is displayed. Toggle is OFF when the number is not dis-

played. (e.g., [1---5---], Toggle Options 1 and 5 are ON, all others are OFF). Press the number on key-

pad to turn toggle ON/OFF.

Figure 3 GS2060/TL260GS Wiring Diagram

DG009391

UDIO/DEF

DSC

A557

PC-LINK

GND

PWR PWR GND GND

SHLD

TL260GS / GS2060

AC AC

RED BLK YEL GRN

Z1 COM Z2 Z3 COM Z4 Z5 COM Z6 Z7 COM Z

AUX+

BELL+

AUX-

BELL-

PGM1 PGM3

EGND

TIP

T-1

PGM2 PGM4

RING R-1

PC1616/1832/1864

GSM R

dio

SIM C

Holder

WARNING!

All connections to the

TL260GS/GS2060 module are power
limited. Do not route any wiring over the
circuit boards. Maintain at least 1”
(25.4mm) separation between circuit
board and wiring. A minimum of 1/4”
(7mm) separation must be maintained at
all points between non-power limited
wiring and power limited wiring.

UA503

NOTE:

For more det

, refer to the

control, p

nel In

tion M

CON 4

To extern

ntenn

Network Connection

(Model TL260GS)
U