Digiplex EVO192, Installation Manual

Page: 50 / 64

46 Reference & Installation Manual
3.3.12 Keypad Tamper Enable
S
ECTION
[006] : O
PTION
[5]
3.3.13 Combus Voltmeter
1. From Normal Mode press and hold the [0] key.
2. Enter the [
INSTALLER CODE
] (Default: 000000).
3. Press [
ACC
].
The voltage may drop during the control panel battery test.
3.4 Programmable Output Options
3.4.1 PGM State
S
ECTION
[006] : O
PTION
[1]
The PGM can provide 50mA to any device connected to it.
3.4.2 PGM Deactivation Mode
S
ECTION
[006] : O
PTION
[2]
3.4.3 PGM Base Time
S
ECTION
[006] : O
PTION
[3]
3.4.4 PGM Override
S
ECTION
[006] : O
PTION
[4]
When the PGM override is enabled, the keypad's on-board PGM will ignore
PGM Activation Events
( section 3.4.6 ) , PGM Deactivation Events ( section
3.4.7 ) , and PGM Timers ( section 3.4.5 ). It will remain in its normal state
until the PGM Override is disabled. This option may be used to test the
PGM connections.
3.4.5 PGM Timer
S
ECTION
[008]
The value programmed in section [008] represents how long the PGM will
remain in its opposite state after being activated. To program the timer,
enter a 3-digit decimal value (000 to 255) in section
[008] . Default: 5
seconds .
3.4.6 PGM Activation Event
S
ECTIONS
[009]
TO
[012]
Enter the sections that correspond to the Event Group, Feature Group,
Start # and End # of the PGM and enter the required data.
3.4.7 PGM Deactivation Event
S
ECTIONS
[013]
TO
[016]
If the PGM Deactivation Option is set to follow the PGM Deactivation event,
the PGM will return to its normal state when the event programmed in
sections
[013] to [016] occurs.
Enter the sections that correspond to the Event Group, Feature Group,
Start # and End # of the PGM and enter the required data.
3.5 EVO641R Programming
3.5.1 Partition Assignment
S
ECTION
[001]: O
PTIONS
[1]
TO
[8]
To assign the keypad to a partition, enable the option that corresponds to
the desired partition.
By default, partitions 1 to 8 are enabled.
3.5.2 Display Access Code Entry
S
ECTION
[003]: O
PTION
[1]
Option [1] OFF=Digits are replaced by a “*“(default)
Option [1] ON=Access Code digits will be displayed
3.5.3 Display Exit Delay Timer
S
ECTION
[003]: O
PTION
[2]
Option [2] OFF=Will not display Exit Delay timer (default)
Option [2] ON=LCD screen will display Exit Delay timer
3.5.4 Display Entry Delay Timer
S
ECTION
[003]: O
PTION
[3]
Option [3] OFF=Will not display the Entry Delay Timer (default)
Option [3] ON=LCD screen will display Entry Delay Timer
3.5.5 Confidential Mode
S
ECTION
[003]: O
PTIONS
[4]
AND
[5]
Section [003]:
Option
[4] OFF=Normal Mode (default)
Option [4] ON=Confidential Mode
Option [5] OFF=LCD screen activated by entering an access code (default)
Option [5] ON=LCD screen activated by pressing a button
3.5.6 Confidential Mode Timer
S
ECTION
[007]
Section [007] determines the amount of time without action before the
keypad enters Confidential Mode. The Confidential Mode Timer can be set
from 005 seconds to 255 seconds.
Default: 120 secs.
3.5.7 Time Display Option
S
ECTION
[003]: O
PTION
[8]
Option [8] OFF=Date displayed as yy/mm/dd (default)
Option [8] ON=Date displayed as dd/mm/yy
3.5.8 Muting
S
ECTION
[004]: O
PTION
[1]
Option [1] OFF=Audible sounds (default)
Option [1] ON=Mute
3.5.9 Beep on Exit Delay
S
ECTION
[004]: O
PTION
[2]
Option [2] OFF=Exit Delay beep disabled
Option [2] ON=Exit Delay beep enabled (default)
3.5.10 Chime on Zone Closure
S
ECTION
[004]: O
PTION
[4]
Option [4] OFF=Chime on Zone Closure disabled (default)
Option [4] ON=Chime on Zone Closure enabled
Option [3] ON = Beep enabled: Module and Bus Troubles
Option [4] OFF = Beep disabled: all Zone Troubles (default)
Option [4] ON = Beep enabled: all Zone Troubles
Option [5] OFF = Keypad's tamper is disabled (default)
Option [5] ON = Keypad's tamper is enabled
Option [1] OFF= PGM is Normally Open (default)
Option [1] ON= PGM is Normally Closed
Option [2] OFF = Deactivates on PGM Deactivation Event (default)
Option [2] ON = PGM will deactivate according to the PGM Timer
Option [3] OFF = PGM Base Time is 1 second (default)
Option [3] ON = PGM Base Time is 1 minute
Option [4] OFF = PGM Override disabled (default)
Option [4] ON = PGM Override enabled
Event Group Feature Group Start # End #
PGM [009] [010] [011] [012]
Event Group Feature Group Start # End #
PGM
[013] [014] [015] [016]