manualshive.com logo in svg

DigiDesign SYNC HD, Manual

Share
Download
DigiDesign SYNC HD Manual Download Page 40

SYNC HD Guide

34

SYNC HD Controls in Pro Tools, SYNC Setup Software Utility, 
and the SYNC HD Front Panel

Table 5. SYNC HD controls in Pro Tools, SYNC Setup software utility, and the SYNC HD front panel

Available from/in:

Parameters

Pro Tools

Front Panel

SYNC Setup Software 

Utility

Device ID

no

yes

no

Clock References

all (Session Setup)

all

all

Positional References

all (Session Setup)

all

all

Sample Rates

all all

all

Pull Rates

yes (Session Setup)

yes

yes

Base Clock 
(Word Clock Out)

no

yes

(“Base Clock”)

yes

(“Word Clock Out”)

Frame Rates

all (Session Setup)

all

all

LTC Output level

yes (Peripherals/Sync)

yes

yes

LTC Servo gain

yes (Session Setup)

yes

no

Freewheel duration

yes (Session Setup)

yes

yes

Video Format (NTSC/PAL)

yes (Session Setup)

yes

yes

VITC Read Lines

yes (Peripherals/Sync)

yes

yes

VITC Generate Lines

yes (Peripherals/Sync)

yes

yes

VITC Insertion Enable

yes (Peripherals/Sync)

yes

yes

Pitch Memory Enable

yes (Peripherals/Sync)

yes

yes

Window Dub

all (Peripherals/Sync)

on/off only

yes, all

Bi-Phase/Tach Pulses/Frame

yes (Peripherals/Sync)

yes

yes

Bi-Phase/Tach Wiring

yes (Peripherals/Sync)

no

no

Gen/Bi-Phase Preset

yes (Session Setup)

yes

yes

GPI 

yes

no

no

VSO

yes (Session Setup)

no

yes

Idle MTC Enable

yes (Peripherals/Sync)

yes

yes

Summary of Contents for SYNC HD








































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands