manualshive.com logo in svg

DigiDesign SYNC HD, Manual

Share
Download
DigiDesign SYNC HD Manual Download Page 26

SYNC HD Guide

20

Video In Format Settings at 
HD Video Reference Rates

When the Clock Reference is set to Video Refer-
ence (HD), SYNC HD automatically sets the 
Video In format (NTSC or PAL) appropriate for 
the selected Video Reference rate, as shown in 
the following table.

With 24-frame and 48-frame rates only, a pop-
up menu lets you set the Video In Format.

Clock Reference, Video Ref In, 
and Video In Settings when 
Importing Avid Video

When you import Avid video media into a ses-
sion, Pro Tools automatically sets the Clock Ref-
erence (HD or SD), Video Reference rate, and 
Video In format appropriate for the imported 
media. 

Video Reference (HD) Rate

Video In Format

Slow PAL 23.976

NTSC

Slow PAL 24

PAL

720p - 23.976

NTSC

720p - 24

PAL (NTSC available)

720p - 25

PAL

720p - 29.97

NTSC

720p - 30

NTSC

720p - 50

PAL

720p - 59.94

NTSC

720p - 60

NTSC

1080i - 47.95

NTSC

1080i - 48

PAL (NTSC available)

1080i - 50

PAL

1080i - 59.94

NTSC

1080i - 60

NTSC

1080p - 24

PAL (NTSC available)

1080p - 25

PAL

1080p - 29.97

NTSC

1080p - 30

NTSC

1080p - 50

PAL

1080p - 59.94

NTSC

1080p - 60

NTSC

Summary of Contents for SYNC HD








































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands