DigiDesign Digi 001 Page 9 Quick Start Manual Download

Page: 9 / 82

Chapter 2: Macintosh Configuration

chapter 2

Macintosh Configuration

Installing the Digi 001 Hardware

Before installing the Pro Tools LE software, first install the Digi 001 card.

To install the Digi 001 card in your Macintosh:

Turn off your computer. Leave it plugged in so that it is grounded.

Open the computer case. If necessary, refer to the manufacturer’s instructions for details.

Remove the rear slot cover and screw of any available PCI expansion slot.

Before handling the Digi 001 card, discharge any static electricity by touching the outer
casing of the power supply.

Remove the Digi 001 card from its anti-static bag.

Hold the card gently by the top edges, and line up its PCI connector with the PCI slot

inside the computer.

PCI card installation for Macintosh Blue & White G3

Summary of Contents for Digi 001



















































































Search results

Summary of Contents for Digi 001

Reviews:

Related manuals for Digi 001

Brands by name

Popular brands

DigiDesign Digi 001, Quick Start Manual

Search results

Summary of Contents for Digi 001

Reviews:

Related manuals for Digi 001

Brands by name

Popular brands