background image

7

4       safeTY PrecauTions - General inforMaTion

 1.

 

Never operate the Skid Hoe without first reading and understanding the 

entire

 operator’s manual. 

 

2.

 

Do not paint over,

 remove or deface any safety signs or warning decals on your equipment.

 3.

 

Follow all safety decals.

 keep them clean and replace them if they become worn, damaged or illegible.

 

4.

 

know your equipment inside and out. know how to operate all controls and know emergency shut down procedures

 5.

 

Keep all stepping surfaces, pedals, and controls free from dirt, grease and oil.

 keep equipment clean to help avoid injury from  

 

slipping or falling when getting on or off equipment

 6.

 

Operate the attachment only in daylight or sufficient artificial light.

 

7.

 

Always carry loads close to the ground. Do not step off platform with load raised.

 

8.

 

Turn off engine before performing maintenance

. All maintenance can be performed with the machine arms lowered. If lift arms  

 

must be left raised for any reason, use a positive lift arm lock to secure the arms in place. Serious damage or personal injury could  

 

result from lift arms accidentally lowering.

 9.

 

To avoid overturning the machine. Reduce speed when driving over rough terrain,

 on a slope, or turning.

10.

 

Check your work area and know where all utility lines are.

 Avoid hitting underground or overhead electrical wires, cables, pipes,  

 

fence posts, gas lines, etc.

11.

 

Never operate equipment while under the influence of

 alcohol, prescription drugs or any other form of illegal recreational drugs  

 

which could inhibit physical and/or mental capacity.

12.

  Do not exceed recomended safe operating load of machine, as machine may become unstable resulting in loss of control.

13.

 

Slow down before turning.

 Sharp turns on any terrain may cause loss of control. 

14.

 

Always lower the loader arms to the ground, 

shut off the engine and remove the key before getting off the unit. v

15.

  Operators, helpers, and other personnel working near the equipment must wear steel-toe safety shoes, safety glasses, and hard  

 

hats as a minimum. Hearing protection, respirators, and personnel protective clothing will be specified in the site-specific Health  

 

and Safety Plan.

16.

  Do not smoke when refuelling. Allow room in the gas tank for expansion. wipe up any spilt fuel. Secure cap tightly when done.

17.

  Be alert to others in the work area. Be sure others know when and where you will be working. Make sure no one is behind 

 

equipment or within 6 metres of it operating.

18.

  Loose fitting clothing, long hair, jewellery and equipment which might become entangled in moving equipment are prohibited while  

 

working near the Skid Hoe.

19.

  The equipment must be shut down and properly locked-out and tagged before repairs or maintenance is performed. Only properly  

 

trained and qualified individuals are permitted to perform 

 

repairs and maintenance.

20.

  Site workers shall not be allowed on the attachment while it is in operation 

21.

  Machinery must be shut down and the key removed before being left unattended.

Summary of Contents for SKID HOE























Reviews: