manualshive.com logo in svg

diagenode Bioruptor Pico, User Manual

Share
Download
diagenode Bioruptor Pico User Manual Download Page 32

32

 

BIORUPTOR

®

 PICO

    MANUAL 

Instructions for Class A digital device, Canada

This  Class  A  digital  apparatus  complies  with  Canadian  ICES-003”  (ICES  =  Interference 
Causing Equipment Standards).

« Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada ». 

Device Placement

Very  specific  placement  conditions  are  applicable  for  the  equipment.  These  placement 
conditions are specified in the technical data of the device for the most part.

Additional placement conditions are described below.

•  Toxic vapors can be produced depending on the heat transfer liquid used and type of operation. Ensure 

sufficient extraction of the vapors.

•  Observe the requirements of the device for electromagnetic compatibility (EMC).

•  Do not cover the ventilation openings.

WARNING!

Rolling away, falling over of the device

Impact, crushing

•   Do not tilt the device.

•  Place the device on a level, non-slip surface with sufficient 

load bearing capacity.

•  Engage the castor brake when setting up the device.

•  Do not place any heavy parts on the device.

1.  

Place the device at a suitable location in the room. Place tabletop devices on a suitable 
table. Support the device for this by reaching under the device.

2.  

The device requires 20 cm of clearance at the front and rear side in order to allow proper 
airflow through the refrigeration unit. 

3.  

The device must be installed at RT (10C – 25°C) and can be placed bellow or at the same 
level of the Bioruptor

Summary of Contents for Bioruptor Pico

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands