manualshive.com logo in svg

DGSHAPE DWX-53DC, Installer'S Manual

Share
Download
DGSHAPE DWX-53DC Installer'S Manual Download Page 2

 

Introduction ............................................................................................................................................................... 2 

ABOUT THE MACHINE .................................................................................................................................................. 3 

Unique features ........................................................................................................................................................ 3 

Pre-installation check ......................................................................................................................................................... 4 

Installation and Installation .......................................................................................................................4 
Installation location ................................................................................................................................................... 5 
Temperature and humidity ........................................................................................................................6 
Installation space .......................................................................................................................................7 

What's in the Box ............................................................................................................................................................... 9 

Installation ........................................................................................................................................................ 11 

PREPARATION TO USE THE MACHINE ................................................................................................................ 12 

Check before operation ........................................................................................................................... 12 

Install the aircraft ............................................................................................................................................................ 15 

Remove the fasteners .............................................................................................................................. 15 
Connect the power cord ........................................................................................................................ 19 
Turn on the power ................................................................................................................................. 21 
Retighten the screws of the air nozzle. ...................................................................................... 22 
Attach the dust collector .......................................................................................................................... 24 
Install the regulator ................................................................................................................... 25 

Connect to a computer...................................................................................................................................................... 29 

System requirements ............................................................................................................................... 29 
Software to be installed ........................................................................................................... 30 
Install software .................................................................................................................. 31 
Connect to a computer ............................................................................................................. 32 
Show VPanel ......................................................................................................................................... 39 
Exiting VPanel ...................................................................................................................................... 40 

Connect multiple units .................................................................................................................................................... 41 

Registering another aircraft ..................................................................................................................... 41 
Switching the Aircraft Operated by VPanel ......................................................................................... 44 
Changing the Name and Images of the Aircraft Displayed on VPanel ..................................................... 45 

Before starting work ....................................................................................................................................................... 47 

Selecting the Aircraft to Use with VPanel for DWX ............................................................................... 47 
Running in the disc changer .................................................................................................... 48 
Perform spindle habituation operations ..................................................................................... 50 
Correcting the cutting position automatically .......................................................................................... 52 
Turn off .................................................................................................................................... 58 

Appendix ........................................................................................................................................................... 59 

Specifications ................................................................................................................................................. 60 

Expansion terminal .................................................................................................................................. 60 
Coordinate ............................................................................................................................................... 61 
Dimensions ............................................................................................................................................. 62 
List of specifications ............................................................................................................................... 66 
System-Requirements for USB Connectivity ........................................................................................... 67 

 
 
 
 
 

 

1 

Tabl

e of 

Con

tent

s 

Summary of Contents for DWX-53DC







































































Reviews:

No comments

Brands by name

Popular brands

Load more brands