DFI KD171 User Manual Download Page 35

Page: 35 / 47

www.dfi.com

Chapter 3

- BIOS Settings

KD171

PXE Boot capability

This field is only available when "Boot Type" is set to “UEFI Boot Type” or “Dual Boot Type”,

and when "Network Stack" is enabled.

Disabled

Suppoort Network Stack

UEFI

IPv4/IPv6

Legacy

Legacy PXE OPROM only

PXE Boot to LAN

Enable or disable Boot into the Pre-boot Execution Environment (PXE) stored in the LAN. This

field is only available when "Boot Type" is set to “Legacy Boot Type” or “Dual Boot Type”, and

when "Network Stack" is enabled.

USB Boot

Enable or disable booting to USB boot devices.

Quiet Boot

Enable or disable booting in text mode.



EFI

Configure boot priorities in this submenu. Press -/+ or F5/F6 to move the highlighted item

down/up the priority list. This field is only available when "Boot Type" is set to “UEFI Boot

Type” or "Dual Boot Type".

Normal Boot Menu

Select a priority arranging method.

Normal

Boot priority is arranged according to the type of the storage devices, and the

configured order.

Advance

Boot priority is arranged according to the configured order regardless of the

type of the storage devices.

►Boot Type Order

Arrange the priority of types of the storage devices.

►Hard Disk Drive/ ►CD/DVD-ROM Drive / ►USB / ►Others

Arrange the priority of the storage devices in each category. The submenu will not be dis-

played when there is no available storage device of the type.



Legacy

Configure boot priorities in this submenu. Re-arrange the order by pressing -/+ or F5/F6 to

move the highlighted item down/up the priority list. This field is only available when "Boot

Type" is set to “Legacy Boot Type” or "Dual Boot Type".

Note:

When a desired LAN port for PXE boot is not listed as a boot device, please con-

firm that the "PXE Boot to LAN", "PXE boot capability", "Network Stack" and the

LAN controller of the said LAN (go to "Advanced" > "PCI Express Configuration")

are enabled. Please press F10 to save the settings and re-start the system board

for the settings to take effect.

InsydeH2O Setup Utility

Rev. 5.0

Help

Esc

Exit

↑/↓

Select Item

←/→

Select Item

F5/F6

Change Values

Enter

Select



SubMenu

Setup Defaults

F10

Save and Exit

InsydeH2O Setup Utility

Rev. 5.0

Help

Esc

Exit

↑/↓

Select Item

←/→

Select Item

F5/F6

Change Values

Enter

Select



SubMenu

Setup Defaults

F10

Save and Exit

Select Normal Boot Option

Priority or Advance Boot

Option Priority

EFI

Boot Device Priority

Normal Boot Menu

►

Boot Type Order

►Hard Disk Drive

►CD/DVD-ROM Drive

►USB

►Others

EFI

EFI Network 0 for IPv4 (00-00-00-00-00-00)

EFI Network 1 for IPv4 (11-11-11-11-11-11)

Boot

<Normal>

►

Boot

►

Boot

Summary of Contents for KD171
















































Search results

Summary of Contents for KD171

Reviews:

Related manuals for KD171

Brands by name

Popular brands

DFI KD171, User Manual

Search results

Summary of Contents for KD171

Reviews:

Related manuals for KD171

Brands by name

Popular brands