DFI KD171 User Manual Download Page 32

Page: 32 / 47

www.dfi.com

Chapter 3

- BIOS Settings

KD171

Smart Fan

Smart Fan is a fan speed moderation strategy that depends on the current system

temperature. When the system temperature goes higher than the Boundary setting, the fan

speed will be turned up to the setting of the Fan Speed Count that bears the same index as

the Boundary field.

SYS Smart Fan/CPU Smart Fan Control

Enable or disable the system smart fan. When disabled, fan speed will not be controllable

according to different system temperatures. Instead, a Fix Fan Speed Count field will be dis-

played to configure at which speed the fan will always be fixed regardless of system tempera-

ture.

▼ SYS Smart Fan/CPU Smart Fan Control = [Enabled]

Boundary 1 to Boundary 4

Set the boundary temperatures that determine the fan speeds accordingly, the value rang-

ing from 0-127℃. For example, when the system temperature reaches Boundary 1 setting,

the fan speed will be turned up to the designated speed of the Fan Speed Count 1 field.

Fan Speed Count 1 to Fan Speed Count 4

Set the fan speed, the value ranging from 1-100%, 100% being full speed. The fans will

operate according to the specified boundary temperatures above-mentioned.

▼ SYS Smart Fan/CPU Smart Fan Control = [Disabled]

Fix Fan Speed Count

Set the fan speed, the value ranging from 1-100%, 100% being full speed. The fans will

always operate at the specified speed regardless of gauged temperatures.

COM Port 1 to COM Port 6

Enables or disables the serial ports (COM). The following bracketed fields will only appear

when the port is enabled.

WDT

Enable or disable the Watchdog Timer (WDT) function. A counter will appear if you select to

enable WDT. Input any value between 1 to 255 seconds.

▼ WDT = [Enable]

COUNTER

Set the timeout value of the WDT — 1-255 seconds.



PC Health Status

This section displays the PC health status.

InsydeH2O Setup Utility

Rev. 5.0

Help

Esc

Exit

↑/↓

Select Item

←/→

Select Item

F5/F6

Change Values

Enter

Select



SubMenu

Setup Defaults

F10

Save and Exit

PC Health Status
Voltage

VBAT

VCORE

VDDQ

+12V

Temperature

System (°C/°F)

CPU (°C/°F)

Fan Speed

SYS FAN

CPU FAN

Advanced

3.072 V

0.784 V

1.184 V

4.939 V

11.616 V

35.0 C/ 95.0 F

42.0 C/ 107.6 F

0 RPM

2561 RPM

►

Advanced

►

Advanced

►

SIO NUVOTON6116D

►

SIO NUVOTON6116D

Summary of Contents for KD171
















































Search results

Summary of Contents for KD171

Reviews:

Related manuals for KD171

Brands by name

Popular brands

DFI KD171, User Manual

Search results

Summary of Contents for KD171

Reviews:

Related manuals for KD171

Brands by name

Popular brands