background image

front tamper key once to start the update.

After finish the firmware download, the LED will start flash in every 0.5

second. At that time, 

please don't remove the battery

, otherwise it

will cause the firmware broken, and the device will no function.

After the LED stop flash, it is recommended that the user power up the

device.  

Caution

:   After   remove   the   battery,   please   wait   about   30

seconds, and then re-install the battery.

Security Network

The device support the security function. When the device included

with a security controller, the device will auto switch to the security

mode. In the security mode, the follow commands need using Security

CC wrapped to communicate, otherwise it will not response.

COMMAND_CLASS_BATTERY

COMMAND_CLASS_NOTIFICATION_V4

COMMAND_CLASS_ASSOCIATION_V2

COMMAND_CLASS_CONFIGURATION

COMMAND_CLASS_SENSOR_BINARY_V2

COMMAND_CLASS_SENSOR_MULTILEVEL_V5

COMMAND_CLASS_WAKE_UP_V2

Function DIP Switch(Motion Sensor only)

There is one function DIP switch in front of the device.

Remove the front cover in the right top of the PCB, and also has mark

“M1” and “M2” for two switch.

M1 M2

Description

ON ON Test Mode and OTA mode.
ON OFF Normal Mode.

OFF ON Normal Mode.
OFF OFF Program Mode. According to the configuration setting 

NO. 5 to set the operation mode.

Operation Mode

There are two modes “Test” and “Normal”. 

“Test Mode” is for the user test the sensor function when installation.

“Normal Mode” for the normal operation.

When the event triggered, normally the LED won't indicated, unless the

battery is in the low level, the LED will flash once. But in the “Test

Mode” the LED also will light ON one second.

When the event triggered, the device will report the messages to the

nodes in the group 1. The messages also include the battery level, the

temperature and the illumination level. The user can switch the report

by   setting   the   configuration   NO.   5   bit4   (illumination)   and   bit5

(temperature), and the configuration NO. 7 bit6 (battery). 

When the event triggered, if the environment luminance is less than

the setting of the value of the configuration NO. 4, the device will emit

the signal to turn ON the lighting equipment, those nodes are in the

group 2. And delay a while to turn OFF the lighting equipment. The

delay time is setting by the configuration NO. 9. 

The   PIR   motion   re-detected   interval,  in  the   “Test  Mode”  fixed   to   6

seconds.   In   the   “Normal   Mode”,   it   according   to   the   setting   of   the

configuration NO. 8.

Notice: 

When the tamper key of the back side is released, the device

always in the “Test Mode”, no matter the DIP switch setting.

5

Summary of Contents for MT 02648













Reviews: