background image

14

CHIPPING

6. If you wish to collect the shredded material, it can be discharged onto a plastic, or similar, 

sheet. To collect the material, simply switch off the machine, move it backwards off the sheet, 

and pick up the sheet by its four corners. 

      Please note: The machine should not be tilted while it is running, as the engine may seize.

7.  Do  not  allow  discharged  material  to  build  up  to  the  point  where  the  discharge  chute  is 

blocked. In the unlikely event that material becomes jammed in the chipper chamber, switch 

off the machine, turn off the fuel tap, lower the clutch lever and disconnect the spark plug 

lead from the spark plug. Latch the discharge chute in the ‘Up’ position and reach into the 

discharge  opening  to  remove  the  offending  material. 

warninG:

  FAILURE  TO  FOLLOW  ALL 

THESE PROCEDURES COULD LEAD TO A SERIOUS INJURY, AS THE ENGINE MAY START WHEN 

THE DISC IS ROTATED BY HAND.

8. Be very careful when feeding long ‘stringy’ material into the hopper, as it can rush out of your 

hands in an instant. 

neVer

 WRAP MATERIAL AROUND YOUR HANDS. ALWAYS BE PREPARED 

TO  INSTANTLY  RELEASE  THE  MATERIAL.  PREFERABLY,  LONG  MATERIAL  SUCH  AS  VINES 

SHOULD BE CUT INTO LENGTHS NO LONGER THAN 500mm.

TO  STOP,  SIMPLY  MOVE  THE  ON-OFF  SWITCH  TO  ‘OFF’.  NEVER  RAISE  THE  DISCHARGE 

CHUTE TO STOP THE MACHINE. REMOVE THE SPARK PLUG LEAD BEFORE CLEARING A JAM 

OR CHECKING THE MACHINE. LEAVE THE CLUTCH ENGAGED WHEN STOPPING. THIS WILL 

REDUCE THE ‘RUN-ON’ PERIOD OF THE ROTOR. After the rotor has stopped, the clutch can be 

moved to the disengage position in readiness for the next start-up.

safe sToppinG proCeDure

ChippinG  (continued)

Summary of Contents for GARDEN CHIPPER 750

























Reviews: