background image

Part No. 3452     Edition: 1      MAY 2013

WARRANTY POLICY

DEUTSCHER MOWERS PTY. LTD. will repair or replace, free of charge, any chipper or part of a chipper that is 

• 

defective in materials or workmanship (or both) for a period of 24 months from the date of purchase. If parts 

or units are replaced, the replacement period will be no longer than 3 months. This does not cover normal 

wear, abuse or incorrect service procedures as set out in the owner’s manual. Parts such as blades, blade 

bolts, wheels and v-belts, which can be subjected to use beyond their normal intended working limits, are 

also excluded.
This warranty is void if parts other than genuine parts have been used or if repairs or modifications have been 

• 

made without the manufactures written authority.
This warranty does not obligate the manufacturer, agents or dealers to cover transport costs incurred in the 

• 

repair or replacement of any defective part. Also, it does not obligate the manufacturer, agents or dealers to 

cover any other costs associated with making the warranty claim. (eg telephone calls)
The engine on this chipper is covered by the engine manufacturer’s warranty supplied with the mower. For 

• 

your nearest engine dealer, phone: 

                   - 

honda m.p.e.:

 1300 2 466 32

                   - 

briggs & stratton:

 1300 274 447  www.briggsandstratton.com

To claim a warranty the owner must return the chipper (at the owners expense)  to an authorized dealer , then 

give the authorized dealer a clear explanation of the defect. A list of authorized dealers can be found on the 

Deutscher Mowers website or the location of the nearest authorized dealer can be determined by telephoning 

the telephone number listed below.
Our goods come with guarantees that cannot be excluded under Australian Consumer Law. You are entitled to 

a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or 

damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality 

and the failure does not amount to a major failure.
The benefits to the owner given by this warranty are in addition to other rights and remedies of the owner under 

a law in relation to goods or services to which the warranty relates.

Manufactured in Australia by: 

DeuTsCher mowers pTy lTD

, 731Creswick Rd, Ballarat, 3350

Telephone :  03  5339 5708     Fax:  03 5339 3189      www.deutschermowers.com.au

remember: proof of purchase is the responsibility of the owner and is necessary prior to warranty work 

being undertaken. only warranty work performed by an authorized dealer using genuine spare parts 

will be eligible for payment, and claims may not be accepted if abuse or other damage has occurred that 

is not considered as normal wear and tear.

for your reCorD

Model: 

 GarDen Chipper 750

Serial Number:  

 

 

Date of Purchase:

Mower Purchased From:

Summary of Contents for GARDEN CHIPPER 750

























Reviews: