background image

7

7. Attach the discharge chute to the machine with the two M8 x 20 bolts, two plain washers and 

two 8mm nyloc nuts as shown below. Tighten the nyloc nuts fully, then back off half a turn. This 

will allow the chute to hinge open and closed. Check that the chute is latching correctly in the 

‘UP’ position and that the microswitch audibly clicks when the chute is being lowered into its 

operating position. 

DO NOT DROP THE CHUTE WHEN UNLATCHING. 

HOLD ONTO THE OUTER END AND LOWER IT DOWN. 

8. A third M8 x 20 bolt plus an 8mm plain washer and an 8mm spring washer have been provided 

for locking the chute in the operating position. With the chute lowered, place the spring washer 

then the plain washer onto the bolt, and insert the bolt through the slot at the base of the chute 

and into the nut that is welded inside the chassis. 

 

9. With the chipper on a level surface, fill the engine with 600mm of the correct engine oil. Check the 

level by using the dipstick. See the engine manual, supplied. Add unleaded petrol to the fuel tank.               

warninG:   when hanDlinG peTrol, Keep away from any naKeD flames, This inCluDes 

The piloT liGhT on Gas applianCes. peTrol fumes are hiGhly VolaTile.

INITIAL ASSEMBLY

Discharge chute

Summary of Contents for GARDEN CHIPPER 750

























Reviews: