background image

15

basiC mainTenanCe

Tools required : 

• 5mm Allen Key (chipper blade replacement)

• Two 13mm ring / open ended spanners. 

 

(or one 13mm spanner plus a ratchet wrench and 13mm socket)

• 17mm open ended spanner for hopper removal.

General

When the machine is stopped for servicing, inspection, or to change an accessory, shut off the 

engine, push down the clutch lever, disconnect the spark plug wire from the spark plug and 

make sure that all moving parts have come to a complete stop. Due to the magneto starting 

system, the engine may start when the cutting means is moved unless the ignition switch is off 

and the spark plug wire is removed from the spark plug. Never rely on the clutch to positively 

disengage the drive mechanism.

Allow the machine to cool before inspection, adjustments etc.

oil check and replacement

The engine oil level should be checked regularly, every 4 hours of operation. For oil replacement, 

see the engine manual.  

air filter cleaning

Check the condition of the air cleaner regularly, in dusty conditions every 4 hours. See engine 

book for cleaning details.

Drive belt adjustment / replacement

The drive belt may become loose after an initial settling in period, after very heavy loads have 

been applied or after an extended period of use.  You can tell if the belt is slipping by a reduction 

in material feed rate or by the belt smoking. 

when ‘slipping’ is suspected, do not continue to 

use the machine.

 Tighten the belt as follows:

•  Switch off the engine and remove the spark plug lead from the spark plug.

•  Using a 13mm spanner, remove the plastic belt guard.

•  Observe the condition of the belt. If it is severely frayed or has a burnt section, it will need 

to be replaced.

MAINTENANCE

12mm deflection

Drive Belt

DriVe belT aDJusTmenT

(3)

(2)

(1)

Summary of Contents for GARDEN CHIPPER 750

























Reviews: