DETROIT 471952 Operator'S Manual Download Page 68 | Manualshive

Page: 68 / 84

background image

1. Allow the engine to run for approximately five minutes at a moderate speed.
2. After the coolant temperature reaches 50°C (122°F), recheck the coolant

level in the surge tank. The cooling system is correctly filled when the
coolant is between the full and low marks on the surge tank.

3. Stop the engine and allow it to cool down. If necessary, fill the surge tank

with approved coolant, Refer to section "How to Select Coolants". Do not
overfill the cooling system as overfilling will cause the surge tank to push
coolant out of the overflow.

How to Select Coolants

How to Select Coolants

Refer to the Coolant Requirements for Engine Cooling Systems (DDC-SVC-
BRO-0002) manual for the most up-to-date coolant information.
Coolants used in Detroit™ engines must meet DFS 93K217 Specification with the
following basic requirements:
• Provide an adequate heat transfer medium.
• Protect against cavitation damage.
• Provide a corrosion/erosion-resistant environment.
• Prevent formation of scale or sludge deposits.
• Be compatible with cooling system hose and seal materials.
• Provide adequate freeze protection.
The concentration of Extended Life Coolant (ELC) corrosion inhibitors will
gradually deplete, at a much slower rate than Standard Life Coolant (SLC)
corrosion inhibitors, during normal engine operation. Corrosion inhibitor limits are
established by the coolant manufacturer. Therefore Detroit™ recommends
following the manufacturer's recommendations as to minimum and maximum
limits.

Extended Life Coolants

Extended Life Coolants (ELC) contain Organic Acid Technology (OAT), which
provides corrosion protection and inhibit liner cavitation. These coolants require
less maintenance over the useful life of the engine.
ELC antifreeze coolants are commercially available from Detroit™ service outlets
and other manufacturers as either concentrated or pre-mixed formulations.
Concentrated coolants should be mixed at 50% (50% coolant/50% water). All
ELCs used must also meet DFS 93K217 specification. Detroit™ requires that these
types of coolants be free of nitrite and phosphate. Detroit™ has found that ELC's
containing nitrite may lead to a breakdown of the coolant and subsequent damage
to the cooling system.

How to Procedures

68

All information subject to change without notice.

Copyright © 2020 DETROIT DIESEL CORPORATION

DDC-SVC-MAN-0217

«
...
66
67
68
69
70
...
»

Summary of Contents for 471952





















































































Reviews:

No comments

Related manuals for 471952

Brand: CIMCO Pages: 24

Brand: Jiecang Pages: 2

695D/925 Series

Brand: Wisco Industries Pages: 6

Brand: YARDMAX Pages: 25

Brand: Landa Pages: 64

Brand: Volvo Penta Pages: 100

Brand: Volvo Penta Pages: 104

Brand: XTM Racing Pages: 6

Brand: Clarke Pages: 18

Brand: Hacker Pages: 8

Brand: Hacker Pages: 8

Brand: Hacker Pages: 38

Brand: Yanmar Pages: 280

Brand: Hino Motors Pages: 216

Brand: Hino Pages: 278

Brand: Yanmar Pages: 84

Brand: Yanmar Pages: 222

Brand: WilTec Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands