manualshive.com logo in svg

Detex AO19, Instructions Manual, Page: 5 / 12

Share
Download
Detex AO19 Instructions Manual Download Page 5

Verify that the device ordered is the correct model for the door application. 

Check for correct handing and size.

Inspect package for possible shipping damages. Carefully cut tape and open cardboard shipping box. Packed into this box you will typically

find arm assembly, door decal(s), complete low energy operator and instruction documents. Remove items and place them carefully aside so
they will not be damaged or lost. Using a #2 Phillips, remove the cover screws and lift bottom edge of cover & pull out.  Remove packing and

inspect all items before continuing.

Receiving Inspection

Installation Preparation

The hanger plate is unique to the Detex Low Energy Automatic Door Operator. It allows the installation to be performed by one

person, quickly and efficiently.

104852 Page 5

Remove the countersunk screws to remove front cover. Screws will be re-used when re-installing cover.
Unit is shipped with screws in the 2 outside hole locations only.
Extra screws are provided in the hardware kit for the remaining screw holes when re-installing the cover.

AO19 Right Hand Push

AO19 Left Hand Push

(PUSH SIDE)

Contact Factory on damages and missing equipment

Front Cover

Hanger Plate

Summary of Contents for AO19













Reviews:

No comments