Detex AO19 Instructions Manual Download Page 1 | Manualshive

Page: 1 / 12

Detex AO19 Instructions Manual Download Page 1

DETEX Low Energy Automatic Door Operator, Twin Door-Push (AO19-2

)

104852 Page 1

For device installation videos,

scan code below or

go to www.detex.com/videos

Table of Contents

Device parts breakdown view...............................................................
Parts list................................................................................................
Hardware List with part numbers & tools required................................

Caution notice, Device description........................................................

Inspection, Front cover removal & Hanger plate prep...........................
Hanger plate installation, Opener installation........................................
120VAC connections, Push arm installation..........................................
Motor-Gearbox installation.....................................................................
Door foot installation, Rod Adjustment..................................................

Low voltage connections.......................................................................

Switch description & location.................................................................

Decal description & location...................................................................

Owner's Copy

Page

2
3
4
4
5
6
7
8
9
10
11
12

Detex Corporation, 302 Detex Drive, New Braunfels, Texas 78130-3045

830-629-2900 / 800-729-3839 / Fax 800-653-3839 / Text photos only: 830-481-6433 / INTERNET: www.detex.com

104852 September 28, 2020 F

Drawing: 104700

For WARRANTY information,

scan code below or

go to www.detex.com/warranty

Should you have a Question/Problem with your Detex device please call Detex Technical Support

from the job site at 1-800-729-3839 and choose option 2 on our menu. Please do not return the

product to the distributor.

1
2
3
...
»

Summary of Contents for AO19













Reviews:

No comments