Desoutter CVI3 Function, User Manual, Page: 32 / 44

Appendix - User info codes _02/2017 - 32 -
Type of
code
Code
no.
Description Resolution procedure
Warning 41 Unauthorized tool 1- The tool connected to the controller is not authorized.
2 Maximum number of battery tool reached or tightening unit associated
doesn't exist anymore
3- Check the ePOD connection and capacity.
Warning 62 Overload of torque 1- Overload of the torque, could be a rehit
2- Check tool cable is not damaged
Warning 201 Replace RTC battery 1- The real time clock backup battery needs to be replaced.
Warning 212 Result not stored 1- It was not possible to persist the tightening result in the controller
2- Contact your Desoutter representative for support
Warning 214 Short circuit 1- Serial peripheral default.
2- Disconnect and reconnect.
3- Check the serial peripheral.
Warning 246 Synchro I/O problem 1- Error detected on synchronisation input
2- Check the configuration of I/O
3- Check the synchronisation cable
Warning 250 Pset corrupted 1- Pset is not defined correctly
2- Check the Pset
Warning 253 Incorrect tool Id 1- Pset is not defined correctly.
2- One tool declared in the Pset is not part of the tightening unit
3- Check the Pset.
Warning 257 Remote start error 1- Verify the tool trigger is correctly pushed
Warning 258 Calibration need Pset mode 1- For tool calibration, the Tightening Unit has to be in Pset mode
2- Change the Tightening Unit mode into Pset mode.
Warning 267 Result transfer error Result transfer error
Warning 273 Debug UsrInfo 1- This UsrInfo is for debug. Contact dev team.
Warning 501 CVILogix user info Message generated by CVILOGIX program
Warning 600 Controller disconnected DCT_MOT_CONTROLLER_DISCONNECTED_PROCEDURE
Warning 601 RESULT NOT OK Result not OK
Error 6 Rotor locked 1-Unable to start tool motor (rotor is locked), change your tool
2-Contact your Desoutter representative for support
Error 7 Motor too hot 1- Tool is locked because its maximum motor temperature has been
reached.
2- Tool will remain locked until the motor temperature comes back to its
normal value.
Error 8 Tool angle fault 1- Problem detected with the tool angle sensor
2- The tool needs maintenance.
3- Contact your Desoutter representative for support
Error 9 Tool invalid param 1- Please check the tool compatiblity.
2- The tool memory cannot be read or is invalid.
3- The tool needs maintenance. If the problem occurs again, contact your
Desoutter representative for support.
Error 12 Tool EEPROM error 1- The tool memory cannot be read or is invalid.
2- The tool needs maintenance. If the problem occurs again, contact your
Desoutter representative for support.
Error 13 Bad tool ground 1- Phase-phase or phase to ground shortcircuit.
2- Disconnect the tool. Contact your Desoutter representative for support.
Error 14 Tq. power default 1- The torque sensor is not corrrectly supplied
2- The tool needs maintenance. If the problem occurs again, contact your
Desoutter representative for support.
Error 18 Torque out of range ! 1- The target torque value is above the tool max. torque.
2- Check Pset settings against tool characteristics.
Error 19 Tool comm. error 1- Tool communication error.
2- Check tool and cable connections. If the problem occurs again, contact
your Desoutter representative for support.
Error 20 Tool LED err. 1-Tool LED are not corrrectly supplied
2- Disconnect and reconnect the tool. If the problem occurs again, contact
your Desoutter representative for support.
Error 23 Unsupported tool 1- The tool connected to the controller is not supported.
2- Contact your Desoutter representative for more information.
Error 29 The battery is empty 1- The battery is discharged. The tool cannot tighten.
2- Recharge the battery.
Error 31 Battery error 1- Abnormal battery voltage, the tool cannot tighten.
2- Recharge the battery. If the problem occurs again, replace the battery.