Desoutter CVI3 Function, User Manual, Page: 25 / 44

Appendix - I/O and events_02/2017 - 25 -
Name Description Status
Enable access
manager
Enable/disable access manager State
Lock display Lock/unlock the controller display. State
Restart Controller Reboots the controller.
Everything must be done by the software before using this input
Rising edge
Reset identifiers Erases all ongoing accepted identifiers fields from CVI3/tool memory in order to guarantee
a correct traceability
Rising edge
Tools commands
Tool validation
forward
Enables the tool to run the selected Pset. Note: the forward and reverse validation can be
done by setting both validations on the same input. When the validation signal falls down,
the tool stops.
State
Tool validation
reverse
Enables the tool run reverse. Note: the forward and reverse validation can be done by
setting both validations on the same input. When the validation signal falls down, the tool
stops.
State
Reset tool locks Reset tool locks, only the none safety tool locks will be affected Rising edge
Tool stop Stops the tool. Rising edge
Tool blue light ctrl
by IO
1 = Tool blue light is controlled by IO
0 = Tool blue light is managed by the controller
State
Tool blue light If "Tool blue light ctrl by IO" is set to 1 (see upward) then:
1 = tool blue light is set to on
0 = tool blue light is set to off
State
Tool green light ctrl
by IO
1 = Tool green light is controlled by IO
0 = Tool green light is managed by the controller
State
Tool green light If "Tool green light ctrl by IO" is set to 1 (see upward) then:
1 = tool green light is set to on
0 = tool green light is set to off
State
Tool red light ctrl by
IO
1 = Tool red light is controlled by IO
0 = Tool red light is managed by the controller
State
Tool red light If "Tool red light ctrl by IO" is set to 1 (see upward) then:
1 = tool red light is set to on
0 = tool red light is set to off
State
Tool yellow light ctrl
by IO
1 = Tool yellow light is controlled by IO
0 = Tool yellow light is managed by the controller
State
Tool yellow light If "Tool yellow light ctrl by IO" is set to 1 (see upward) then:
1 = tool yellow light is set to on
0 = tool yellow light is set to off
State
Tool white light ctrl
by IO
1 = Tool white light is controlled by IO
0 = Tool white light is managed by the controller
State
Tool white light If "Tool white light ctrl by IO" is set to 1 (see upward) then:
1 = tool white light is set to on
0 = tool white light is set to off
State
Reset of redundancy
error
Resets redundancy error only. State
Pset commands
Pset select bit (0..7) Used to select Psets.
These inputs must be in the desired state BEFORE the activation of the cycle start input.
If the selected Pset is zero, there is no Pset selected.
State
Select previous Pset Select lower number Pset. Rising edge
Select next Pset Select higher number Pset. Rising edge
External stop abort
Pset
This input is used with proximity detectors to end immediately Pset running.
The user can choose which state or transition will stop the Pset: No, Rising, Falling,
Change, High, Low.
When a Pset is aborted with this input, the Pset result is NOK.
Rising edge
or state
External stop to next
step
This input is used with proximity detectors to end the running step.
The user can choose which state or transition will stop the Pset : No, Rising, Falling,
Change, High, Low.
The user can also choose the step result when the stop request occurs: OK, NOK,
Monitoring (Monitoring means that the result is computed depending on monitoring
requested).
Rising edge
or state
Synchro in Step synchronisation input.
The step starts when a transition to 0 is detected.
State
External Tool inputs
bit (0..9)
Indicates that these inputs can be used by an external tool (to generate OK/NOK report for
example)
State