background image

!

- If there is a problem with the device, first look to the troubleshooting part of this manual. If you cannot solve the 

problem, contact your dealer.

- All the system needs to be protected from water, direct sunlight and shocks.

- Before using your motorized cylinder, 

Locking way (right or left handed door) 

and

 Number of turns 

should be adjusted 

properly. Otherwise, the device will not work in the correct way and maybe broken. 

- For emergency conditions, we recommend you to put the keys in an accessible place (like car, bag etc.)

GENERAL INFORMATION and WARNINGS

- If there is any problem with the door or the locking mechanism, first of all, those problems have to be solved. The door's 

mechanical parts and locking mechanism have to work properly. 

- Auto-rotating parts of the device can cause injuries during installation. BE CAREFUL!
- If you are leaving your home for an extended period of time, first fully charge your motorized cylinder and take your 

mechanical key with you. If you would leave more than 2 months, after charging your motorized cylinder, either shift the 
motorized cylinder to childlock mode or leave your device as it is connected to charger. Otherwise, the batteries of your 
product would die due to deep discharge.

Summary of Contents for utopic R OD CONVERT














Reviews: