manualshive.com logo in svg

Desert Aire CM3530 Series, Installation And Operation Manual, Page: 49 / 50

Share
Download
Desert Aire CM3530 Series Installation And Operation Manual Download Page 49

49

5  

Appendix 

5

.1   Internal Web Page

 

The programmable controller is preprogrammed by Desert Aire to include a web page allowing  

 

a virtual remote display to be used from any node on the facilities computer network. Simply  

 

attach an ethernet cable from your facilities computer network to the RJ45 port of the 

 

controller. Always check with your IT department before connecting this device to your

 

network.

 

The ethernet port of the controller has a factory default of DHCP for the TCP/IP address. To  

 

obtain the current address, see Section 2.3.3.3 for the ethernet port setup, Figure 29. A static  

 

TCP/IP address can be set from this screen. Refer to your IT department to obtain a static  

 

TCP/IP address. Browse the IP address assigned to the dehumidifier, enter the appropriate  

 

credentials, [user – Desert-Aire, password – 18485] and select the DISPLAY tab. Logging is  

 

also available from this web page. Wait a few moments for initialization and use your mouse 

 

to click the keys. Key combinations are defined on the bottom of this web page.

Desert Aire - CM3530 Manual

Summary of Contents for CM3530 Series



















































Reviews:

No comments