manualshive.com logo in svg

Desert Aire CM3530 Series, Installation And Operation Manual, Page: 4 / 50

Share
Download
Desert Aire CM3530 Series Installation And Operation Manual Download Page 4

4

Extended Warranty:

Your Desert Aire unit may have extended warrantees beyond this Standard Limited Warranty document.  
Extended warrantees are only available at the time of the purchase of the original equipment. These extended 
warrantees are covered under a separate document and their terms and conditions are separate from this document.  
It is mentioned in this document for informational purposes only.  Any Extended Warranties will be identified on the 
Warranty Validation Letter.

Any and all incidental or consequential damages are expressly excluded from this warranty.  Some states do not allow 
the exclusion of incidental or consequential damages for personal injury, so the above limitations may not apply to you 
for certain damages.  This warranty gives you specific legal rights, and you may also have other rights, which vary 
from state to state.  No person or representative is authorized to make any warranty or assume any liability not strictly 
in accordance with the aforementioned.

Inquiries regarding warranty matters should be addressed to: 

 

 

 

 

 

 

Desert Aire Corp

 

 

 

 

 

 

c/o Service Manager 

 

 

 

 

 

 

N120 W18485 Freistadt Road

 

 

 

 

 

 

Germantown, WI  53022

 

 

 

 

 

 

PH: (262) 946-7400

 

 

 

 

 

 

TOLL FREE: (800) 443-5276 

 

 

 

 

 

 

FAX: (262) 946-7401 

 

 

 

 

 

 

E-MAIL: [email protected] 

 

Additional copies of this manual can be purchased for a nominal fee from Desert Aire. Desert Aire also posts the 
most current revision of our I/O Manuals on our website. For a digital copy of the I/O Manual for your unit revision, 
please submit request to the contact information listed above.

Desert Aire - CM3530 Manual

Summary of Contents for CM3530 Series



















































Reviews:

No comments