Desert Aire CM3530 Series Installation And Operation Manual Download Page 20 | Manualshive

Page: 20 / 50

Desert Aire CM3530 Series Installation And Operation Manual Download Page 20

20

Figure 13

To return to the MAIN MENU, press the

Esc

key. The user remains logged

in for 30 minutes after the password is entered. During this time, the Login

screen reads “Logged In For” and the seconds left before the password

expires. To login without entering the password, while this message is shown,

press the

Prg

key.

2.3.3.1 Commissioning (Figure 14)

Selecting the COMMISSIONING MENU from the Service Menu displays the

COMMISSIONING MENU (Figure 14). This menu allows the operator to

select the Configuration, Airflow Setup, Current Conditions, Commissioning

Test, Motor Phasing and BMS Setup. To return to the Service Menu, press the

Esc

key.

Figure 14

2.3.3.1.1 Configuration – Blower Setup (Figure 15)

Selecting the CONFIGURATION from the Commissioning Menu

displays the BLOWER SETUP screen (Figure 15). The blower

can be set for either CONTINUOUS or AUTOMATIC. Only set the

blower to automatic if a wall mount sensor is used.

Desert Aire - CM3530 Manual

«
...
18
19
20
21
22
...
»

Summary of Contents for CM3530 Series



















































Reviews:

No comments