manualshive.com logo in svg

Desert Aire CM3530 Series, Installation And Operation Manual, Page: 48 / 50

Share
Download
Desert Aire CM3530 Series Installation And Operation Manual Download Page 48

48

4.4 

Suction Line, Liquid & DHU Temperature Sensor

 

These temperature sensors are a resistive NTC Bulb type device with a 10 foot cable. The  

 

temperature range is -58.0°F to 212.0°F and the environmental rating is IP67. The failure mode  

 

of this device will display a reading of -623.3°F if the sensor is open, and display a reading of  

 

687.3°F if the sensor is shorted. The Desert Aire replacement part number for the Supply Air  

 

Temperature Sensor is available by calling our service department.

4.5 

Zone Air Temperature and Relative Humidity Sensor

 

This sensor is a communicating device which sends Modbus data out from address 190. If  

 

communication is lost from this device, an alarm is activated. The Desert Aire replacement part  

 

number for the Zone Air Temperature and Relative Humidity Sensor is available by calling our

 

service department.

4.6 

Reheat Condenser and Evaporator Bypass Differential Air Pressure Sensors

 

These sensors have a range of 0.0”wc to 2.0”wc. The output of this device is a 0.25 VDC at  

 

0.0”wc and 4VDC at 2.0”wc. The Desert Aire replacement part number is available by calling  

 

our service department.

4.7 

EC Blower Differential Air Pressure Sensor

 

The EC Blower Differential Air Pressure Sensor has a range of either 0-10.0” wc, or 0-25” wc.  

 

The output of this device is a 0.25 VDC at 0.0” wc and 4 VDC at either 10.0” wc or 25.0” wc.  

 

The Desert Aire replacement part number is available by calling our service department.

Desert Aire - CM3530 Manual

Summary of Contents for CM3530 Series



















































Reviews:

No comments