![background image](http://html1.mh-extra.com/html/desa/vvf36/vvf36_owners-operation-and-installation-manual_2486194029.webp)
www.desatech.com
56131H
9
LIGHTING
INSTRUCTIONS
1. STOP! Read the safety information,
page.8.
.. Set.HI-LO.knob.to.the.lowest.setting.
3.. Turn.off.all.electrical.power.to.appliance.
4.. Open.control.access.panel.
5.. Push.in.gas.control.knob.slightly.and.turn.
clockwise.
.to.the.OFF.position.
6. Wait five (5) minutes to clear out any gas.
Then smell for gas, including near the
floor. If you smell gas, STOP! Follow “B”
in the safety information, page 28. If you
don’t smell gas, go to the next step.
7.. The.pilot.is.located.by.the.main.burner.
8.. Turn. knob. on. gas. control. counterclock-
wise.
.to.the.PILOT.position.
9.. Push.in.control.knob.all.the.way.and.hold.
in.. Immediately. light. pilot. by. pressing.
ignitor button until a flame appears one
minute.after.pilot.is.lit..Release.knob.and.
it.will.pop.back.up..Pilot.should.remain.lit..
If it goes out, repeat steps 5 through 9.
• If knob does not pop out when released,
stop.and.call.gas.supplier.
• If pilot will not stay lit after several tries,
turn. gas. control. knob. to. OFF. and. call.
your.service.technician.or.gas.supplier.
10..Turn.gas.control.knob.counterclockwise.
. to. the. ON. position.. Knob. can.
be.turned.to.ON.only.if.control.knob.is.
popped.out.
OFF
P
IL
O
T
ON
LO
HI
P
ILOT
E
A
16AI
7
TPTH
TP
TH
Gas.Control.
Knob
Flame.Adjustment.
Knob
Position.
Indicator
Figure 59 - Millivolt Control Valve
Figure 60 - Pilot
Thermopile
Pilot.Burner
Piezo Ignitor
Thermocouple
OPERATION
Continued
TO TURN OFF GAS
TO APPLIANCE
1.. Turn.off.wall.switch.
.. Turn.off.all.electric.power.to.appliance.if.
service.is.to.be.performed.
3.. Remove.control.access.panel.
4.. Push.in.gas.control.knob.slightly.and.turn.
clockwise.
.to.OFF..Do.not.force.
5.. Replace.control.access.panel.
MILLIVOLT SySTEM
11..Set.HI-LO.knob.to.desired.setting.
1..Turn.on.all.electric.power.to.appliance.
ELECTRONIC SySTEM
•. If. burner. will. not. stay. lit. after. several.
tries, flip wall switch to OFF and call your
service.technician.or.gas.supplier.
E
A
O
L
H
I
L
PI OT
Inlet.
Pressure
Figure 61 - Electronic Control Valve
Outlet.
Pressure
Flame.
Adjustment.
Knob
From.Gas.
Supply
To.
Main.
Burner
Figure 62 - Electrode
LIGHTING
INSTRUCTIONS
1.. STOP!. Read. the. safety. information.
page.8.
.. Set. thermostat. to. lowest. setting. (if. ap-
plicable).
3.. Turn.off.wall.switch.
4.. Open.control.access.panel.or.louver.
5. Smell for gas, including near the floor. If
you smell gas, STOP! Follow “B” in the
safety information,
page.8..If.you.don’t.
smell gas, go to the next step.
6.. The.electrode.is.located.by.main.burner.
7.. Turn.main.burner.wall.switch.to.the.ON.
position.for.ignition..There.will.be.a.spark.
at.the.electrode.
8.. Replace. control. access. panel. or. louver.
once there is a flame at the burner.