![background image](http://html1.mh-extra.com/html/desa/vvf36/vvf36_owners-operation-and-installation-manual_2486194022.webp)
www.desatech.com
56131H
FIREPLACE INSTALLATION
Continued
You.may.test.blower.for.operation.by.turning.
control.knob.clockwise.just.until.it.clicks.on.
which.is.the.full.on.position..Adjust.fan.speed.
to.lowest.setting.(this.should.be.no.more.than.
1/4.of.a.turn.clockwise).
FRONT
OFF
P
IL
O
T
ON
LO
HI
PI
LOT
E
A
16AI
7
TPTH
TP
TH
Figure 38 - Installing Remote Receiver
(HRC100)
Gas.
Valve
To.Thermopoile
Receiver.Clip
Terminal.
Wires
Plastic.Mounting.Clips
9-Volt.Battery
White
Red
OPTIONAL WIRELESS HAND-HELD
REMOTE CONTROL INSTALLATION
Note: If using an optional wireless hand-
held remote control, wall switch is no longer
operational.
NOTICE: Only use alkaline bat
-
teries (not included).
Installing HRC100 Model Remote Control
(Millivolt Models Only)
1.. Remove. lower. louver. access. panel. in.
fireplace (see step 1 of
Wall Switch Instal-
lation
, page 21).
.. Disconnect.wall.switch.wires.from.termi-
nals. marked.TH. and.TPTH. (see. Figure.
35, page 21).
3.. Slide. 9-volt. battery. into. clip. on. back. of.
remote.receiver.and.connect.battery.termi-
nals.to.battery..Mount.receiver.onto.bracket.
with.clips.provided.(see.Figure.38).
9-Volt.Battery
Battery.
Housing
Figure 39 - Installing Battery in Hand-
Held Remote Control Unit (HRC100)
Battery.
Cover
Terminal.
Wires
Remote.Control.Unit
Sensor.
Tag
Figure 37 - Connecting Blower
Accessory to Power Supply
For.Optional.
Fan.Kit
From.Blower.
Assembly
4.. Connect.white.wire.to.control.valve.ter-
minal. TH. and. red. wire. to. TPTH.. Move.
remote. select. switch. to. the. REMOTE.
position.
5.. Replace.louvered.access.panel.by.follow-
ing.reverse.steps.on.page.1.
6.. Remove.battery.cover.on.back.of.hand-
held.remote.(see.Figure.39)..Remove.and.
discard.sensor.tag.
7.. Attach. terminal. wires. to. 9-volt. battery..
Place.battery.into.housing.
8.. Replace. battery. cover. onto. hand-held.
remote.
9.. Set.selector.switch.on.receiver.to.the.OFF.
position.if.you.will.be.away.from.unit.for.
an.extended.period.of.time.
Installing SKYTECH/WRC Model Remote
Control (Electronic Models Only)
1.. Remove. lower. louver. access. panel. in.
fireplace (see step 1 of
Wall Switch Instal-
lation
, page 21).
2. If a wall switch was installed, it must be
removed. from. ignition. control. circuit. for.
remote. to. work. properly.. Remove. wire.
nuts. from. switch. connection. at. ignition.
control module. Using wire nut, connect
transformer.(blue).wire.to.remaining.wire.
connected. to. control. terminal. marked.
P.SW (see Figure 34, page 21).
3. The receiver does not require a battery.
To install, plug extension cord into one of
the.outlet.receptacles.on.outlet.box..Plug.
receiver.unit.into.extension.cord.and.igni-
tion.module.into.receiver.unit.(see.Figure.
40, page 23).
4.. Replace.louvered.access.panel.by.follow-
ing.reverse.steps.on.page.1.
5.. Activate. handset. battery. by. removing.
insulating tab on back (see Figure 41,
page.3).