background image

www.desatech.com

107886-01J

21

TROUBLESHOOTING

Continued 

POSSIBLE CAUSE

1. Gas  leak. 

See  Warning 

statement on page 21

2. Control valve defective

1. Foreign matter between con-

trol valve and burner

2. Gas  leak. 

See  Warning 

statement on page 21

1. Not enough combustion/ven-

tilation air

OBSERVED PROBLEM

Gas odor even when control knob 

is in OFF position

Gas odor during combustion

Moisture/condensation  noticed 

on windows

REMEDY

1. Locate  and  correct  all  leaks 

(see 

Checking  Gas  Connec-

tions,

 page 12)

2. Replace control valve

1. Take  apart  gas  tubing  and 

remove foreign matter

2. Locate  and  correct  all  leaks 

(see 

Checking  Gas  Connec-

tions,

 page 12)

1. Refer to 

Air for Combustion 

and Ventilation requirements

 

(page 5)

REPLACEMENT PARTS

Note:

 Use only original replacement parts. This 

will  protect  your  warranty  coverage  for  parts 

replaced under warranty. 

PARTS UNDER WARRANTY

Contact  authorized  dealers  of  this  product.  If 

they canʼt supply original replacement part(s), 

call DESA Heating Productsʼ Technical Service 

Department at 1-866-672-6040.
When  calling  DESA  Heating  Products,  have 

ready
•  your name
•  your address
•  model and serial numbers of your heater 
•  how heater was malfunctioning
•  type of gas used (propane/LP or natural gas)
•  purchase date
Usually, we will ask you to return the part to the 

factory.

PARTS NOT UNDER WARRANTY

Contact authorized dealers of this product. If they 

canʼt  supply  original  replacement  part(s),  call 

DESA Heating Products at 1-866-672-6040 for 

referral information.
When  calling  DESA  Heating  Products,  have 

ready
•  model number of your heater 
•  the replacement part number

ACCESSORIES

Purchase these heater accessories from your local 

dealer. If they can not supply these accessories, 

call DESA Heating Products at 1-866-672-6040 

for referral information. You can also write to the 

address listed on the back page of this manual.

EQUIPMENT SHUTOFF VALVE 
GA5010

For all models.

 Equipment shutoff valve with 

1/8" NPT tap.

FAN KITS - GA3250T

For all models.

 Provides better heat distribution. 

Makes heater more efficient. Complete installation 

and operating instructions included.
Thermostatically-controlled, blower turns itself on 

and off as required.

ELECTRONIC IGNITOR KIT - GA435 
Not Shown

For all piezo ignitor models. 

Provides  easier 

lighting of the pilot.

Summary of Contents for VP20BT

























Reviews: