background image

www.desatech.com

116035-01J

4

3.  Never install the fireplace 

• in a recreational vehicle
• in windy or drafty areas where curtains 

or other combustible (flammable) objects 
can  make  contact  with  the  fireplace 
front

• in high traffic areas

4.  Turn  fireplace  off  and  let  cool  before 

servicing,  installing  or  repairing.  Only  a 
qualified  service  person  should  install, 
service or repair this fireplace. Have fire

-

place  inspected  annually  by  a  qualified 
service person.

5.  You  must  keep  control  compartments, 

burners  and  circulating  air  passages 
clean.  More  frequent  cleaning  may  be 
needed  due  to  excessive  lint  and  dust 
from  carpeting,  bedding  material,  etc. 
Turn off the gas valve and pilot light before 
cleaning fireplace.

6.  Have venting system inspected annually by 

a qualified service person. If needed, have 

SAFETy

Continued

PRODUCT IDENTIFICATION

Figure 1 - Top and Rear Direct-Vent Fireplaces

Rear Vent 
Flue Collar

Nailing 
Flange

Top Vent 
Flue Collar

Door Latch

Log Set

Ember 
Tray

Junction 
Box

Lower Louver Panel

Control Valve Variable 
Input Adjustment

Piezo Ignitor with 
Optional Remote and 
Blower Control Mount

Upper 
Louver 
Panel

Glass Door 
Assembly

LOCAL CODES

venting system cleaned or repaired. See 

Cleaning and Maintenance

, page 38.

7.  Do not use any solid fuels (wood, coal, 

paper,  cardboard,  etc.)  in  this  fireplace. 
Use only the gas type indicated on fire

-

place nameplate.

8.  This appliance, when installed, must be 

electrically grounded in accordance with 
local  codes  or,  in  the  absence  of  local 
codes, with the 

National Electrical Code, 

ANSI/NFPA 70.

9.  Do not use fireplace if any part has been 

exposed to or under water. Immediately 
call a qualified service person to arrange 
for replacement of the unit.

10. Do  not  operate  fireplace  if  any  log  is 

broken.

11. Do not operate fireplace with glass door 

removed, cracked or broken.

12. Provide adequate clearances around air 

openings.

Install and use fireplace with care. Follow all 
local  codes. In the absence  to local  codes, 
use the current 

National Fuel Gas Code ANSI 

Z223.1/NFPA 54*

 (USA).

*Available from:

American National Standards Institute, Inc.

1430 Broadway

New York, NY 10018

National Fire Protection Association, Inc.

Batterymarch Park

Quincy, MA 02269

Summary of Contents for (V) CD36T(N

























































Reviews: