background image

 

 

 

 

 

INSTALLATION & OPERATING INSTRUCTIONS 

 

Modern FullView DV Gas Fireplace Insert Heater 

Cosmetically Incredible & Highly Efficient at 84% Steady State Efficiency 

 

MODEL NO. FV44-M 

DOCUMENT: FV44-M-PF2-0814 

INSTALLER:

 Leave this manual with the appliance. 

CONSUMER: 

Retain this manual for future reference. 

 

INSTALLATEUR

 : Laissez cette notice avec l’appareil. 

CONSOMMATEUR

 : Conservez cette notice pour consulta-

tion ultérieure. 

WARNING: If the information in this manual is not followed 
exactly, a fire or explosion may result causing property dam-
age, personal injury or loss of life.

 

Do not store or use gasoline or other flammable  
vapors and liquids in the vicinity of this or any 
other appliance. 

WHAT TO DO IF YOU SMELL GAS 

 

Open windows. 

 

Do not touch electrical switches. 

 

Do not try to light any appliance. 

 

Extinguish any open flame. 

 

Do not use the phone in your building. 

 

Immediately call your gas supplier from a neighbor's 
phone.  Follow the gas supplier’s instructions. 

 

If you cannot reach your gas supplier, call the fire 
department. 

 

Installation and service must be performed by a 
qualified installer, service agency or the gas suppli-
er. 

WARNING 

Do NOT use this appliance if any part has been under water.  
Immediately call a qualified service technician to inspect the 
appliance and to replace any part of the control system and 
any gas control, which has been under water.

 

AVERTISSEMENT :  Assurez-vous de bien               suivre 
les instructions donné dans cette notice pour réduire au min-
imum le risque d’incendie ou pour éviter tout dommage 
matéeriel, toute blessure ou la mort. 

 

 

Ne pas entreposer ni utiliser d'essence ni d'autres vape-
rurs ou liquides inflammables dans le voisinage de cet 
appareil ou de tout autre appareil. 

 

QUE FAIRE SI VOUS SENTEZ UNE ODEUR             
DE GAZ:   

 

Ne pas tenter d'allumer d'appareil. 

 

Ne touchez à aucun interrupteur.  Ne pas vous  servir 
des téléphones se trouvant dans le batiment où vous 
vous trouvez. 

 

Appelez immédiatement votre fournisseur de gaz depuis 
un voisin.  Suivez les instructions du fournisseur. 

 

Si vous ne pouvez rejoindre le fournisseur de gaz, appe-
lez le service dos incendies. 

 

L'installation et service doit être exécuté par un    quali-
fié installer, agence de service ou le fournisseur de gaz. 

Summary of Contents for FV44-M














































Reviews: