background image

www.desatech.com

116035-01J

34

Figure 63 - On/Off Hand-Held Remote 

Control Unit HRC100

Control 
Button

Indicator 
Light

ON/OFF SERIES MODEL HRC100

Hold control button on the hand-held remote 
until burner turns on. Hold the control button 
again until burner turns off (see Figure 63).
TO LOCK press both buttons on hand-held 
remote control until light stops flashing. Hand-
held remote control is now locked. If the fire 
is on it will be turned off automatically. In the 
locked state, the light will not light up when 
any button is pressed.
TO  UNLOCK  press  both  buttons  together 
on  hand-held  remote  control  until  the  light 
stops flashing. The hand-held remote is now 
unlocked.

THERMOSTAT SERIES MODEL HRC200

The hand-held remote can be operated using 
either the manual mode (MANU) or thermo

-

static mode (AUTO) (see Figure 64). To select 
Fahrenheit/Centigrade mode display, carefully 
press the ˚C/˚F mode button with the end of a 
paper clip or similar blunt object.

Manual Mode

1.  Press  the  POWER  and  LOCK  buttons 

together to turn on the hand-held remote 
control.

2.  Press  the  MANU  button  to  turn  on  the 

fireplace.

3.  Press  the  POWER  and  LOCK  buttons 

together to turn off the fireplace.

Auto (Thermostatic) Mode

1.  Press  the  POWER  and  LOCK  buttons 

together to turn on the hand-held remote 
control.

2.  Press AUTO button to select this mode.
3.  Set  the  desired  room  temperature  by 

pressing the TEMP + or - buttons.

4.  Press  the  POWER  and  LOCK  buttons 

together to turn off the fireplace

Note: Do not leave hand-held remote in the 
AUTO mode close to the fireplace. The radiant 

Figure 64 - Thermostat Hand-Held 

Remote Control Unit HRC200

LOCK

MANU

AUTO

ºC/ºF

TEMP

POWER

ROOM
TEMP

SET
TEMP

AUTO

Turns 
Hand-Held 
Remote On 
or Off and 
Allows You 
to Choose 
the Manual 
Setting

Selects 

AUTO 

Mode

°C/°F Mode 
Button

Locks 
System to 
Prevent 
Accidental 
Ignition

Turns 
Burners 
On or Off

Increases or 
Decreases 
Room 
Temperature in 
AUTO Mode

Digital Display Shows 
Temperature and Settings

heat from fireplace will turn off the fireplace. 
Ideally, place the hand-held remote in the cen-
ter of the room facing towards the fireplace.
Note: Do not hold the hand-held remote for 
a long time. Body temperature will affect its 
operation in the AUTO mode.

Safety Features

When away from home for an extended period 
of time or as a child safety feature to prevent 
accidental ignition of the fireplace, the receiver 
ON/OFF/REMOTE  switch  should  be  in  the 
OFF position.

Auto Shutoff Feature

1.  If  the  average  room  temperature  reaches 

a range of 82° F (28° C) to 92° F (33° C), 
the hand-held remote control will perform a 
safety override and shut the fireplace off. This 
feature is not available in the MANU mode.

2.  The  receiver  continuously  receives  signals 

from  the  hand-held  remote  to  control  the 
room temperature. If the hand-held remote 
is  misplaced,  obstructed  or  for  any  reason 
cannot transmit to the receiver, the receiver 
will shut off the fireplace. This will occur in 8 
or more minutes depending upon location of 
remote transmitter and strength of batteries.

Key Pad Lock Feature

This feature allows the user to lock/unlock the 
keypad on the hand-held remote in the MANU 
or AUTO  mode  to  prevent  inadvertent  op

-

eration (i.e. children operating the hand-held 
remote control, etc.). The keypad is locked in 
either on or off. Press the POWER and LOCK 
buttons together to turn the unit on or off.

OPERATION 

Continued

MILLIVOLT MODELS

Summary of Contents for (V) CD36T(N

























































Reviews: