105536
5
5
For more information, visit www.desatech.com
For more information, visit www.desatech.com
Example:
A 165 model heater requires one of the following:
• a two-car garage door (16 ft. [4.88 m] wide opening) raised four
inches (10.16 cm)
• a single-car garage door (9 ft. [2.74 m] wide opening) raised seven
inches (17.78 cm)
• two, thirty-inch (76.20 cm) windows raised twelve inches (30.48
cm)
WARNING: Provide a fresh air opening of at least
three square feet (2,800 square cm) for each 100,000
BTU/HR rating. Provide extra fresh air if more heaters
are being used. The minimum ventilation require-
ments must be followed to avoid risks associated
with carbon monoxide poisoning. Make certain these
requirements are met prior to operating heater.
VENTILATION
FUELS
Use only kerosene, #1/#2 diesel/fuel oil, JET A or JP-8 fuels.
Heavier fuels such as No. 2 fuel oil or No. 2 diesel fuel may also be
used but will result in:
• noticeable odor
• additional fuel filter maintenance
• the need for nontoxic, anti-icer additives in very cold weather
Do not use fuels heavier than No. 2 grade or heavy oils such as oil
drained from crankcases. These heavy oils will not ignite properly
and will contaminate the heater.
IMPORTANT:
Use a KEROSENE ONLY (blue) or DIESEL ONLY
(yellow) storage container. Be sure storage container is clean. For-
eign matter such as rust, dirt, or water will cause the ignition control
assembly to shut down heater. Foreign matter may also require
heater's fuel system to be frequently cleaned.
WARNING: Use only kerosene, #1/#2 diesel/fuel
oil, JET A or JP-8 fuels to avoid risk of fire or explo-
sion. Never use gasoline, oil drained from crank-
cases, naphtha, paint thinners, alcohol or other highly
flammable fuels.
TO START HEATER
1.
Follow all ventilation and safety information.
2.
Fill fuel tank with kerosene, #1/#2 diesel/fuel oil, JET A or JP-
8 fuels.
3.
Attach fuel cap.
4.
For thermostat models 55T, 70T, 115T, and 165T, turn ther-
mostat knob clockwise to the high position.
5.
Plug heater’s power cord into approved, grounded, three-wire
extension cord. Extension cord must be at least six feet (1.8
meters) long.
Extension Cord Size Requirement
6 to 10 feet (1.8 to 3 meters) long, use 18 AWG (0.75 mm
2
)
rated cord
11 to 100 feet (3.3 to 30.5 meters) long, use 16 AWG (1.0
mm
2
) rated cord
101 to 200 feet (30.8 to 61 meters) long, use 14 AWG (1.5
mm
2
) rated cord
6.
Plug extension cord into standard 120 volt/60 hertz, 3-prong
grounded outlet.
Note:
Ignitor will preheat for five seconds,
then heater will start.
7.
For thermostat models 55T, 70T, 115T, and 165T, adjust ther-
mostat knob to the desired setting.
Note:
A cold heater may
affect the thermostat setting. This thermostat is a general-heat-
ing control. It is not intended for precise temperature control.
Adjust thermostat until heater cycles at the desired setting.
TO STOP HEATER
Unplug extension cord from outlet.
TO RESTART HEATER
1.
Unplug extension cord from outlet and wait 10 seconds. (Wait
two minutes if heater has been running.)
2.
Repeat steps under To Start Heater.
OPERATION
IMPORTANT: Review and understand the warnings
in the
Safety Information section. They are needed to
safely operate this heater. Follow all local ordinances
and codes when using this heater.
FUELS
VENTILATION
OPERATION
