background image

www.desatech.com

122493-01C

13

INSTALLATION

Continued

4.  Place logs in their proper position on heater 

base (see 

Installing Logs,

 page 16).

5.  Center heater base and logs front-to-front 

and side-to-side in fireplace.

6.  Carefully  remove  logs  without  moving 

heater base.

7.  Mark  screw  locations  through  holes  in 

mounting  brackets  (see  Figure  12).  If 

installing in a brick-bottom fireplace, mark 
screw locations in mortar joint of bricks.

8.  Remove heater base from fireplace.
9.  Drill holes at marked locations using 3/16" 

drill bit.

10. Attach  base  assembly  to  fireplace  floor 

using two masonry screws (in hardware 

package) (see Figure 12).

Figure 12 - Attaching Base Assembly to 

Fireplace Floor

Masonry 

Screw

Mounting 
Bracket

CONNECTING TO GAS SUPPLY

  WARNING:  This  appliance 

requires  a  1/2"  NPT  (National 

Pipe Thread) inlet connection to 

the pressure regulator.

 WARNING: A qualified service 

person must connect heater to gas 

supply. Follow all local codes.

  CAUTION:  Never  connect 

propane/LP heater directly to the 

propane/LP supply. Propane/LP 

heaters require an external regu-

lator  (not  supplied).  Install  the 

external regulator between the 

heater and propane/LP supply.

 WARNING: For natural gas 

units,  never  connect  heater  to 

private  (non-utility)  gas  wells. 

This  gas  is  commonly  known 

as wellhead gas.

Installation Items Needed

Before installing heater, make sure you have 
the items listed below.
•  external regulator (supplied by installer)
•  piping (check local codes)
•  sealant (resistant to propane/LP gas)
•  equipment shutoff valve *
•  test gauge connection *
•  sediment trap
•  tee joint
•  pipe wrench
* A  CSA  design-certified  equipment  shutoff 
valve with 1/8" NPT tap is an acceptable al

-

ternative to test gauge connection. Purchase 

the optional CSA design-certified equipment 

shutoff valve from your dealer.

For  propane/LP  gas,  installer  must  supply 
an external regulator. External regulator will 
reduce  incoming  gas  pressure.  You  must 
reduce  incoming  gas  pressure  to  between 
11"  and  14"  of  water.  If  you  do  not  reduce 
incoming gas pressure, heater regulator dam

-

age could occur. Install external regulator with 
vent  pointing  down  as  shown  in  Figure  13. 
Pointing vent down protects it from freezing 

rain or sleet.

Figure 13 - External Regulator With Vent 

Pointing Down

Propane/LP 
Supply Tank

External 
Regulator 

with Vent 

Pointing 

Down

Summary of Contents for HDL18N





























Reviews: