background image

www.desatech.com

122493-01C

23

OBSERVED PROBLEM

Heater  produces  unwanted 

odors

Heater shuts off in use (ODS 
operates)

Gas odor even when control 

knob is in OFF position

Gas odor during combustion

POSSIBLE CAUSE

1. Heater burning vapors from 

paint,  hair  spray,  glues, 
cleaners,  chemicals,  new 
carpet,  etc.  (See 

IMPOR-

TANT

 statement above)

2. Low fuel supply (propane/

LP only)

3. Gas  leak. 

See  Warning 

statement above

1. Not  enough  fresh  air  is 

available

2. Low line pressure

3. ODS/pilot  is  partially 

clogged

1. Gas  leak. 

See  Warning 

statement above

2. Control valve defective

1. Foreign  matter  between 

control valve and burner

2. Gas  leak. 

See  Warning 

statement above

REMEDY

1. Open  window  and  venti

-

late room. Stop using odor 

causing  products  while 

heater is running

2. Refill supply tank (propane/

LP only)

3. Locate and correct all leaks 

(see 

Checking  Gas  Con-

nections

, page 14)

1. Open  window  and/or  door 

for ventilation

2. Contact  local  natural  or 

propane/LP gas company

3. Clean  ODS/pilot  (see 

Cleaning and Maintenance

page 19)

1. Locate and correct all leaks 

(see 

Checking  Gas  Con-

nections,

 page 14)

2. Replace control valve

1. Take apart gas tubing and 

remove foreign matter

2. Locate and correct all leaks 

(see 

Checking  Gas  Con-

nections,

 page 14)

TROUbLESHOOTING

Continued

 WARNING: If you smell gas

•  Shut off gas supply.

•  Do not try to light any appliance.

•  Do not touch any electrical switch; do not use any phone in your 

building.

•  Immediately call your gas supplier from a neighbor’s phone. Fol-

low the gas supplier’s instructions.

•  If you cannot reach your gas supplier, call the fire department.

Operating heater where impurities in air exist may create odors. Cleaning supplies, paint, paint 
remover, cigarette smoke, cements and glues, new carpet or textiles, etc., create fumes. These 
fumes may mix with combustion air and create odors. These odors will disappear over time.

Summary of Contents for HDL18N





























Reviews: