background image

www.desatech.com

122493-01C

7

1.  Determine the volume of the space (length 

x width x height).

 

Length x Width x Height =__________cu. ft. 
(volume of space)

 

Example:

 Space size 20 ft. (length) x 16 ft. 

(width) x 8 ft. (ceiling height) = 2,560 cu. ft. 

(volume of space)

 

If  additional  ventilation  to  adjoining  room 

is supplied with grills or openings, add the 

volume of these rooms to the total volume 
of the space. 

2.  Multiply the space volume by 20 to determine 

the maximum Btu/Hr the space can support.

 

  ________ (volume of space) x 20 = (Maxi-
mum Btu/Hr the space can support)

 

Example:

  2,560  cu.  ft.  (volume  of  space)  x 

20 = 51,200 (maximum Btu/Hr the space can 

support)

3.  Add the Btu/Hr of all fuel burning appliances 

in the space.

 

Vent-free fireplace 

 

 __________ Btu/Hr

 

Gas water heater* 

 

 __________ Btu/Hr

 

Gas furnace 

   __________ Btu/Hr

 

Vented gas heater 

   __________ Btu/Hr

 

Gas fireplace logs 

 

 __________ Btu/Hr

 

Other gas appliances* +  __________ Btu/Hr

 

Total 

=  __________ Btu/Hr

 

* Do not include direct-vent gas appliances. 

Direct-vent  draws  combustion  air  from  the 

outdoors and vents to the outdoors.

 

Example:

 

 

Gas water heater 

 

 __________ Btu/Hr

 

Vent-free fireplace 

 __________ Btu/Hr

 

Total 

=  __________ Btu/Hr

4.  Compare  the  maximum  Btu/Hr  the  space 

can support with the actual amount of Btu/Hr 

used.

 

  _______ Btu/Hr  (maximum  the  space  can 
support) 

 

  _______ Btu/Hr (actual amount of Btu/Hr 
used)

 

Example:

  51,200  Btu/Hr  (maximum  the 

space can support) 

 

 

71,500 Btu/Hr (actual amount of 

Btu/Hr used)

The space in the example is a confined space 

because the actual Btu/Hr used is more than the 

maximum  Btu/Hr  the  space  can  support.  You 
must  provide  additional  fresh  air. Your  options 
are as follows:
A.  Rework worksheet, adding the space of an 

adjoining room. If the extra space provides an 

unconfined space, remove door to adjoining 

40,000
31,500
71,500

AIR FOR COMbUSTION AND VENTILATION

Continued

Figure 2 - Ventilation Air from Inside Building

Or 

Remove 

Door into 
Adjoining 

Room, 
Option 

Ventilation Grills  

Into Adjoining Room, 

Option 2 

Ventilation

Grills Into

Adjoining 

Room,

Option 1

12" 

12" 

room or add ventilation grills between rooms. 

See 

Ventilation Air From Inside Building

.

B.  Vent  room  directly  to  the  outdoors.  See 

Ventilation Air From Outdoors

, page 8.

C.  Install a lower Btu/Hr fireplace, if lower Btu/Hr 

size makes room unconfined. 

If the actual Btu/Hr used is less than the maxi-

mum Btu/Hr the space can support, the space is 
an unconfined space. You will need no additional 

fresh air ventilation.

 WARNING: If the area in which 

the heater may be operated does 

not meet the required volume for 

indoor combustion air, combus-

tion and ventilation air shall be 

provided by one of the methods 

described  in  the 

National  Fuel 

Gas Code, ANSI Z223.1/NFPA 54

the 

International Fuel Gas Code

or applicable local codes.

VENTILATION AIR

Ventilation Air From Inside Building 

This fresh air would come from an adjoining 

unconfined  space.  When  ventilating  to  an 

adjoining unconfined space, you must provide 
two permanent openings: one within 12" of the 
ceiling and one within 12" of the floor on the 
wall connecting the two spaces (see options 1 
and 2, Figure 2). You can also remove door into 
adjoining room (see option 3, Figure 2). Fol

-

low the 

National Fuel Gas Code ANSI Z223.1/

NFPA 54 Air for Combustion and Ventilation

 for 

required size of ventilation grills or ducts.

Summary of Contents for HDL18N





























Reviews: