background image

www.desatech.com

123721-01E

20

oPeraTioN

Continued

Figure 27 - Pilot

Ignitor Electrode

Pilot Burner

Thermocouple

 

Note: You may be running this fireplace 
for the first time after hooking up to gas 

supply. If so, the control knob may need 
to be pressed in for 30 seconds or more. 

This will allow air to bleed from the gas 

system.

• If control knob does not pop out when 

released,  contact  a  qualified  service 
person or gas supplier for repairs.

6.  With control knob pressed in, press and 

release ignitor button. This will light pilot. 
The pilot is attached to the front burner. If 
needed, keep pressing ignitor button until 
pilot lights.

 

Note:  If  pilot  does  not  stay  lit,  refer  to 
Troubleshooting, page 24. Also, contact a 

qualified service person or gas supplier for 

repairs. Until repairs are made, light pilot 

with match. To light pilot with match, see 

Manual Lighting Procedure

, page 21

.

7.  Keep control knob pressed in for 30 sec

-

onds after lighting pilot. After 30 seconds, 
release control knob.

 

Note:  If  pilot  goes  out,  repeat  steps  3 
through 7. 

8.  Turn control knob counterclockwise 

 

to  desired  heating  level.  The  burner 
should light. Set control knob to any heat 
level between HI and LO.

9.  To leave pilot lit and shut off burners only, 

turn control knob clockwise 

 to the 

PILOT position.

 CAUTION: Do not try to ad-

just heating levels by using the 

equipment shutoff valve.

LIGHTING 

INSTRUCTIONS

 WARNING: You must operate 

this  fireplace  with  the  screen 

in  place.  Make  sure  fireplace 

screen  is  installed  before  run-

ning fireplace.

NOTICE: During initial operation 

of  new  fireplace,  burning  logs 

will  give  off  a  paper-burning 

smell.  Open  window  to  vent 

smell.  Operate  fireplace  on  HI 

position to burn off odor. This 

will only last a few hours.

1.  STOP!  Read  the  safety  information, 

page 19.

2.  Make sure equipment shutoff valve is fully 

open.

3.  Turn control knob clockwise 

 to the 

OFF position.

4.  Wait five (5) minutes to clear out any gas. 

Then  smell  for  gas,  including  near  the 
floor. If you smell gas, STOP! Follow “B” 
in the safety information,page 19. If you 
don’t smell gas, go to the next step.

5.  Turn  control  knob  counterclockwise 

  to  the  PILOT  position.  Press  in 

control  knob  for  five  (5)  seconds  (see 
Figure 26). 

Figure 26 - Control Knob In the OFF 

Position

Ignitor 
Button

Control Knob

Summary of Contents for CCFPDFT





































Reviews: