background image

www.desatech.com

123721-01E

11

iNsTallaTioN

Continued

Figure 7 - Rough Opening for Installing 

in Corner 

Figure 6 - Rough Opening for Installing 

in Wall 

43

5

/

16

"

30

5

/

8

"

61

1

/

4

"  

26

7

/

8

"

Figure 8 - Attaching Fireplace to Wall Studs 

Nailing 
Flanges

Nails or 
Wood 

Screws

Wall Studs

 

Note:  If  not  installing  blower  accessory, 
you may wish to run electrical wiring to 
your fireplace for future blower installation 

(see Accessories, page 33). Use only ap-

proved three-wire electrical wiring.

 WARNING: If pre-wiring, do 

not connect wiring to any electri

-

cal source at this time.
Install fireplace electrical outlet 

and  connect  wiring  to  outlet 

before connecting to electrical 

source.  The  fireplace  electri

-

cal  outlet  is  included  with  the 

GA3450TA blower accessory.
Only  use  the  fireplace  electri

-

cal  outlet  supplied  with  the 

GA3450TA blower accessory.

Note:  A  qualified  installer  should  make  all 

electrical connections.

3.  Install gas piping to fireplace location. This 

installation includes an approved flexible 
gas line (if allowed by local codes) after 
the equipment shutoff valve. The flexible 
gas line must be the last item installed on 
the gas piping.

4.  If  you  have  not  installed  hood,  follow 

instructions on page 9.

5.  Carefully  set  fireplace  in  front  of  rough 

opening with back of fireplace inside wall 
opening.

6.  Attach  flexible  gas  line  to  fireplace  gas 

regulator.  See 

Connecting  Equipment 

Shutoff Valve to Heater Control,

 page 16.

7.  Bend four nailing flanges on outer casing 

with pliers (see Figure 8).

8.  Attach fireplace to wall studs using nails 

or wood screws through holes in nailing 
flange.

9.  Check all gas connections for leaks. See 

Checking Gas Connections

, page 17.

10. If  using  optional  trim  kit,  install  the  trim 

after final finishing and/or painting of wall. 
See instructions included with trim acces

-

sory for attaching trim.

IMPORTANT:

  When  finishing  your  firebox, 

combustible  materials  such  as  wall  board, 

gypsum board, sheet rock, drywall, plywood, 
etc. may be butted up next to the sides and 
top edge of the firebox. Combustible materi

-

als  should  never  overlap  the  firebox  front 
facing.

 WARNING: Do not allow any 

combustible/noncombustible 

materials to overlap the firebox 

front facing.

26 

7

/

8

"

26 

7

/

8

"

3/4" Off
The Floor
Minimum

15 

1

/

4

"

Summary of Contents for CCFPDFT





































Reviews: