background image

Models: 

(ST,PF,CR,CL)DVDNV/DPV, 

DNE/DPE

Designer 

Series Direct 

Vent Gas 

Fireplace

 

IF ThE INFoRMaTIoN IN ThESE INSTRuCTIoNS IS NoT 

FoLLowED  ExaCTLy, a  FIRE  oR  ExPLoSIoN  May 

RESuLT  CauSING  PRoPERTy  DaMaGE,  PERSoNaL 

INjuRy oR LoSS oF LIFE.

– 

Do  not  store  or  use  gasoline  or  other  flammable 

vapors and liquids in the vicinity of this or any other 

appliance.

–  whaT To Do IF you SMELL GaS
 

•  Do not try to light any appliance.

 

•  Do not touch any electrical switch; do not use any 

phone in your building.

 

•  Immediately call your gas supplier from a neighbor's 

phone. Follow the gas supplier's instructions.

 

•  If you cannot reach your gas supplier, call the fire 

department.

–  Installation  and  service  must  be  performed 

by  a  qualified  installer,  service  agency  or  the 

gas supplier.

waRNING: Improper installation, adjustment, alteration, 

services or maintenance can cause injury or property 

damage. Refer to this manual. For assistance or additional 

information consult a qualified installer, service agency 

or the gas supplier.   

This  appliance  may  be  installed  in  an  aftermarket*, 

permanently located, manufactured home (uSa only) or 

mobile home, where not prohibited by local codes.

This  appliance  is  only  for  use  with  the  type  of  gas 

indicated  on  the  rating  plate.  This  appliance  is  not 

convertible for use with other gases, unless a certified 

kit is used. 

*  aftermarket: Completion of sale, not for purpose of resale, from the 

manufacturer.

waRNING

INSTaLLER: Leave this manual with the appliance.
CoNSuMER: Retain this manual for future refer-

ence.

53D0419  4/13  Rev. 17

420200
6000DV cover

DuE To hIGh TEMPERaTuRES, ThE aPPLIaNCE 

ShouLD  BE  LoCaTED  ouT  oF  TRaFFIC aND 

away FRoM FuRNITuRE aND DRaPERIES.
ChILDREN aND aDuLTS ShouLD BE aLERTED To 

ThE haZaRDS oF hIGh SuRFaCE TEMPERaTuRE 

aND ShouLD STay away To aVoID BuRNS oR 

CLoThING IGNITIoN.
youNG  ChILDREN  ShouLD  BE  SuPERVISED 

whEN ThEy aRE IN ThE SaME RooM aS ThE 

aPPLIaNCE.
CLoThING oR oThER FLaMMaBLE MaTERIaL 

ShouLD  NoT  BE  PLaCED  oN  oR  NEaR  ThE 

aPPLIaNCE.
KEEP ThE RooM aREa CLEaR aND FREE FRoM 

CoMBuSTIBLE  MaTERIaLS,  GaSoLINE, aND 

oThER FLaMMaBLE VaPoRS aND LIquIDS.

Installation and Operating 

Instructions

Summary of Contents for DVDNV

















































Reviews: