background image

1

W415-0210 / R / 02.27.08

$10.00

INSTALLATION 

AND

OPERATION INSTRUCTIONS

Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON L4M 4Y8 Canada 

 (705)721-1212 

 fax(705)722-6031

www.napoleonfireplaces.com 

 [email protected]

CERTIFIED UNDER CANADIAN AND AMERICAN NATIONAL STANDARDS: CSA 2.33 

 ANSI Z21.88 FOR VENTED GAS FIREPLACE HEATERS.

If the information in these instructions are 
not followed exactly, a fire or explosion 
may result causing property damage, 
personal injury or loss of life.

- Do not store or use gasoline or other 
flammable vapors and liquids in the vicinity 
of this or any other appliance.

- WHAT TO DO IF YOU SMELL GAS:
 

Do not try to light any appliance.

 

Do not touch any electrical switch; do  

 

not use any phone in your building.

 

Immediately call your gas supplier from  

 

a neighbor's phone.  Follow the gas  

 supplier’s 

instructions.

 

If you cannot reach your gas supplier,  

 

call the fire department.

- Installation and service must be 
performed by a qualified installer, service 
agency or the supplier.

SAFETY INFORMATION

CERTIFIED FOR CANADA AND UNITED STATES USING ANSI/CSA METHODS.

GD36NTR

BGD36NTR

NATURAL GAS MODEL

GD36PTR

BGD36PTR

PROPANE GAS MODEL

BGD

36

Illust

rated

!

WARNING

INSTALLER:  LEAVE THIS MANUAL WITH THE APPLIANCE.

CONSUMER:  RETAIN THIS MANUAL FOR FUTURE REFERENCE.

NorthlineExpress.com

http://www.northlineexpress.com

Toll-Free 1-866-667-8454

Summary of Contents for GD36NTR





































Reviews: