background image

FRENCH PG. 59

W415-1596 / B / 10.12.18

ADD MANUAL TITLE 

Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada / 103 Miller Drive, Crittenden, Kentucky, USA, 41030

Phone 1 (866) 820-8686 • www.napoleonfi replaces.com • [email protected]

CERTIFIED TO THE CANADIAN AND AMERICAN NATIONAL STANDARDS: 

CSA 2.22 AND ANSI Z21.50 FOR VENTED DECORATIVE GAS APPLIANCES

INSTALLER: 

Leave this manual with the appliance

CONSUMER: 

Retain this manual for future reference

ADD PRODUCT CODE HERE (TRADE GOTHIC LT STD FONT)

NATURAL GAS MODELS:

PROPANE GAS MODELS:

Product Name / Code

(MUST use title from Price Book)

ADD ____ ILLUSTRATED

ADD PRODUCT IMAGE

CSA / 

INTERTEK

LOGO

SAFETY INFORMATION

- Do not store or use gasoline or other 

fl ammable vapors and liquids in the vicinity of 

this or any other appliance.

WHAT TO DO IF YOU SMELL GAS

:

•  Do not try to light any appliance.

•  Do not touch any electrical switch; do not 

use any phone in your building.

•  Immediately call your gas supplier from a 

neighbour’s phone. Follow the gas    

supplier’s   instructions.

•  If you cannot reach your gas supplier, call 

the fi re department.

- Installation and service must be 

performed by a qualifi ed installer, service 

agency, or the supplier.

This appliance may be installed in an aftermarket, 

permanently located, manufactured home (USA 

only) or mobile home, where not prohibited by 

local codes.

This appliance is only for use with the type of gas  

indicated on the rating plate. This appliance is 

not convertible for use with other gases, unless 

a certifi ed kit is used. 

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly 

could result in serious injury, death, or 

property damage.

WARNING

!

ENGLISH 

$10.00

FOR INDOOR USE ONLY

IF INSTAL OPERATION, ADD SERIAL 

NUMBER LABEL HERE

IF SEPARATE MANUALS, ADD “PLACE 

BARCODE LABEL ON THE OWNER’S MANUAL”

HDX40PT-2

HDX40NT-2

High Definition Series

(HDX40-2 illustrated)

HDX40NT

-2 ILL

USTR

ATED

HDX40NT

-2 ILL

USTRÈ

SAFE

TY BARRIER

ÉCR

AN DE PR

OTEC

TION

INSTALLATION AND 

OPERATION MANUAL 

Summary of Contents for HDX40NT-2

















































































































Reviews: