manualshive.com logo in svg

Denyo DCA-150ESK, Instruction Manual

Share
Download
Denyo DCA-150ESK Instruction Manual Download Page 54

8.  Handling of battery

 

A 

CAUTION

BATTERY

■   Battery generates flammable gases.

Improper  handling  may  lead  to  explosion

or  serious  injury.

*  Battery  should be  charged in a well ventilated 

location.  Otherwise,  flammable gases are 

accumulated which  may be ignited and exploded.

* When connecting a booster cable,  do not jumper 

the terminals  (+  and —).  Otherwise,  the flammable 

gases generated from  the battery may be ignited 

and exploded by  sparks.

*  For maintenance of the machine,  disconnect the 

cable on  the ground side.

■   The battery acid is  dilute  sulfuric acid.  Improper 

handling will cause  unexpected bums.

*  When the battery  acid gets  on your clothes  or skin,  wash it  out with a large volume of 

water immediately.  If it gets in your eyes, wash with a large volume  of water 

immediately and consult your doctor.

-   In  the worst case,  it will put out your eyes.

■   For checking or handling of the  battery, be  sure to  stop the  engine in advance.

-   53  -

Summary of Contents for DCA-150ESK
















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands