manualshive.com logo in svg

Denyo DCA-150ESK, Instruction Manual

Share
Download
Denyo DCA-150ESK Instruction Manual Download Page 10

A 

CAUTION

Operator

■   Do not  operate the machine,  if operator  is  tired too much  or  drinks  some 

alcohol or take  some drugs.

*  Otherwise,  it may cause unexpected accidents  or injury.

Ш  During checking or maintenance,  be  sure to put on suitable clothes  and protectors.

*  Do  not put on baggy clothes,  necklace,  etc.,  because they  are  easily caught by 

projections  which may  cause injuries.

A 

CAUTION

Noise

■   This machine  generates large noise,  if the door is 

open.  Surrounding to large noise may  cause  hearing 

trouble.

*  Close  and lock the  door during operation.

*  If opening the  door is  necessary  during operation, 

be  sure to put  on the ear protector.

A 

CAUTION

Connection  to house wiring

■   Before  connecting this machine  to any building's  electrical  system,  a licensed 

electrician must install  an isolation(transfer)  switch.

*  Serious  injury or death may result without this transfer  switch.

-   9  -

Summary of Contents for DCA-150ESK
















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands