Denison Hydraulics P07 C-mod, Service Information, Page: 79 / 80

Ordering Code P07/110 - 02R1C - C10 - 00 - M2
Pump service
Displacement, max*
07 - 6.7 in
3
/rev.
110 - 109,8 cm
3
/rev.
Shaft
02
-Keyed - SAE 44-1 (D) (P07)
- ISO 3019/2 G40N (P110)
03 -Splined -SAE 44-4 (D) (P07)
- ISO 3019/2 K40N (P110)
06- Keyed - DIN 6885 40mm (P110)
07- Splined DIN 5480 40mm (P110)
Shaft rotation
(viewed from shaft end)
R -CW (standard, high speed)
L -CCW (standard, high speed)
Fluid class
1
-compatible with Buna N
4 -compatible with EPR
5 -compatible with Viton
Design letter
Primary controls
C
-Pressure compensator
E -Electric stroker
H -Hydraulic stroker
J -Low torque limiter *1100-1850 lbs-in., 124-209Nm
K -High torque limiter *over 1850 lbs-in., 209 Nm
L -Load sensing
R -Rotary servo
V - Low torque limiter with Load sensing *1100-1850 lbs-in.,
124-209Nm
W - High torque limiter with Load sensing *over 1850 lbs-in., 209 Nm
X - 24 VDC PQ high response (pending)
* Minimum torque values to maintain 5000 psi, 345 bar at
1800 rpm. Consult DENISON Hydraulics for minimums
at lesser pressures and speeds.
Omit-Standard model
M2- Special modification to standard units
NP- No paint
Modification
O
No pump mounted
1- Auxiliary pump (only) with M- modification
(user must advise attitude of rear pump/s mounting. For
ordering two
standard or three or more units refer to order-
ing code for multiple units)
Rear drive mounting
(Appropriate coupling and seals are included)
O- None
M -Rear drive blanking plate
A -SAE 82-2 (A) flange, SAE 16-4 (A) shaft
G- SAE 82-2 (A) flange, SAE 22-4 (B) shaft
B -SAE 101-2/4 (B) flange, SAE 22-4 (B) shaft
Q -SAE 101-2/4 (B) flange, SAE 25-4 (BB) shaft
C -SAE 127-2/4 (C) flange, SAE 32-4 (C) shaft
N -SAE 127-2/4 (C) flange, SAE 38-4 (CC) shaft
D -SAE 152-4 (D) flange, SAE 44-4 (D&E) shaft
Z -ISO 3019/2 (100 B4HW) flange, K25N shaft
Y -ISO 3019/2 (125 B4HW) flange, K32N shaft
X -ISO 3019/2 (160 B4HW) flange, K40N shaft
T -ISO 3019/2, (180 B4HW) flange, K40N shaft
L- ISO 3019/2, (180 B4HW flange, DIN 40-18 shaft
Secondary controls
O
-None
P -*Pressure compensator override
J -*Torque limiter override (low) 1100-1850 in-lbs., 124-209 Nm
K -*Torque limiter override (high) over 1850 in-lbs., 209 Nm
(*E, H & R primary controls only)
Primary control options
1
-Standard maximum volume screw, without indicator
2 -Handwheel maximum volume control without indicator
(available on C, J, K, L, V & W primary controls only)
3 -Maximum volume screw with cam position potentiometer
(pending)
4 -Maximum volume screw with cam position LVDT
(pending)
5 -Maximum volume screw with cam position indicator
6 -Handwheel maximum volume control with cam position poten-
tiometer (pending)
7 -Handwheel maximum volume control with cam position LVDT
(pending)
8 -Handwheel maximum control with cam position indicator
(available on C, J, K, L, V & W primary controls only)
Available control combinations
C10, C20, C50, C80
E10, E50, E1P, E5P,
E1J, E5J, E1K, E5K,
H10, H50, H1P, H5P,
H1J, H5J, H1K, H5K
R10, R50, R1P, R5P,
R1J, R5J, R1K, R5K
J10, J20, J50, J80
K10, K20, K50, K80
L10, L20, L50, L80
V10, V20, V50, V80
W10, W20, W50, W80
PUMP ORDERING CODE
79
www.comoso.com