background image

TECHNICAL DATASHEET

 

CliQ II DIN Rail Power Supply 

24V 480W 1 Phase / DRP024V480W1B

□ 

 

 

  

All parameters are specified at 25°C ambient and AC input unless otherwise indicated.

 

  www.DeltaPSU.com (November 2020, Rev. 07)  

 

2

 

Specifications 

Input Ratings / Characteristics 

 

Nominal Input Voltage 

100-240Vac 

Input Voltage Range 

85-264Vac 

Nominal Input Frequency 

50-60Hz 

Input Frequency  Range 

47-63Hz 

DC Input Voltage Range* 

120-375Vdc 

Input Current 

< 5.00A @ 115Vac, < 3.00A @ 230Vac 

Efficiency at 100% Load 

> 91.0% @ 115Vac, > 92.0% @ 230Vac 

Max Power Dissipation 

0% load  < 2.9W @ 115Vac, < 2.7W @ 230Vac 

 

100% load  < 47W @ 115Vac, < 41W @ 230Vac 

Max Inrush Current (Cold Start) 

< 35A @ 115Vac & 230Vac 

Power Factor 

> 0.96 @ 115Vac, > 0.95 @ 230Vac 

Leakage Current 

< 3mA @ 240Vac 

*Fulfills the test conditions for DC input. DC input safety approval can be obtained upon request. 

 

 

Output Ratings / Characteristics** 

 

Nominal Output Voltage 

24Vdc 

Factory Set Point Tolerance 

24Vdc ± 2% 

Output Voltage Adjustment Range 

24-28Vdc 

Output Current 

20.0A (continuously operating at 24V) 

30.0A (Power Boost for 5 seconds at 24V, refer to the details in 

the Functions section) 

40.0A (Power Boost for 2 seconds at 24V, refer to the details in 

the Functions section) 

 

Output Power 

480W (continuously operating at 24V) 

720W (Power Boost for 5 seconds at 24V, refer to the details in 

the Functions section) 

960W (Power Boost for 2 seconds at 24V, refer to the details in 

the Functions section) 

Line Regulation 

< 0.5% (@ 85-264Vac input, 100% load) 

Load Regulation 

< 1.0% (@ 85-264Vac input, 0-100% load) 

PARD*** (20MHz) 

< 150mVpp 

Rise Time 

< 100ms @ nominal input (100% load) 

Start-up Time 

< 1,000ms @ nominal input (100% load

)

 

Hold-up Time 

> 20ms @ 115Vac & 230Vac (100% load

)

 

Dynamic Response  

(Overshoot & Undershoot O/P Voltage) 

± 5% @ 85-264Vac input, 10-100% load 

(Slew Rate: 0.1A/μs, 50% duty cycle @ 5Hz)

 

Start-up with Capacitive Loads 

10,000µF Max 

**For power de-rating from 50°C to 75°C, see power de-rating on page 3. 

***PARD is measured with an AC 

coupling mode, 5cm wires, and in parallel with 0.1μF ceramic capacitor & 47μF electrolytic capacitor.

 

 

 

 

 

Summary of Contents for DRP024V480W1B Series

















Reviews: