Delta DRP024V480W1B Series Technical Data Sheet Download Page 16

TECHNICAL DATASHEET

 

CliQ II DIN Rail Power Supply 

24V 480W 1 Phase / DRP024V480W1B

□ 

 

 

  

All parameters are specified at 25°C ambient and AC input unless otherwise indicated.

 

  www.DeltaPSU.com (November 2020, Rev. 07)  

 

16

 

Others 

Conformal Coating 

The Protective Coating Technology 

Delta Electronics Group has designed the perfect dipping technique which penetrates everywhere including 

under device, and prevents leakage. The conformal coating dipping can be applied to PCBAs or circuit board. 

The coating preserves the performance of precision electronic primarily by preventing ionizable contaminants 

such as salt from reaching circuit nodes, where the material slumps around sharp edges. This can be a problem 

especially in highly conversing atmosphere. 

 

 

PFC – Norm EN 61000-3-2 

Line Current Harmonic content 

Typically, the input current waveform is not sinusoidal due to the periodical peak charging of the input capacitor. 

In industrial environment, complying with EN 61000-3-2 is only necessary under special conditions. Complying 

to this standard can have some technical drawbacks, such as lower efficiency as well as some commercial 

aspects such as higher purchasing costs. Frequently, the user does not profit from fulfilling this standard, 

therefore, it is important to know whether it is mandatory to meet this standard for a specific application.

 

 

 

Attention 

Delta provides all information in the datasheets on an “AS IS” basis and does not offer any kind of warranty through the information for 

using the product. In the event of any discrepancy between the information in the catalog and datasheets, the datasheets shall prevail 

(please refer to 

www.DeltaPSU.com

 for the latest datasheets information). Delta shall have no liability of indemnification for any claim 

or action arising from any error for the provided information in the datasheets. Customer shall take its responsibility for evaluation of 

using the product before placing an order with Delta. 

 

Delta reserves the right to make changes to the information described in the datasheets without notice. 

 

 

Summary of Contents for DRP024V480W1B Series

















Reviews: