background image

PM[B]sense 

-   16   -

 

V1.3

 

Address 

Description 

Format 

11 

PM10 in µg/m

3

 (x10). 

Measurement averaged over 10 s and updated every sec-
ond. 

16-bit Integer 

12 

PM1.0 in N° of particles/ml. 

Measurement averaged over 60 s and updated every 10 s. 

16-bit Integer 

13 

PM2.5 in N° of particles/ml. 

Measurement averaged over 60 s and updated every 10 s. 

16-bit Integer 

14 

PM10 in N° of particles/ml. 

Measurement averaged over 60 s and updated every 10 s. 

16-bit Integer 

15 

PM1.0 in µg/m

3

 (x10). 

Measurement averaged over 60 s and updated every 10 s. 

16-bit Integer 

16 

PM2.5 in µg/m

3

 (x10). 

Measurement averaged over 60 s and updated every 10 s. 

16-bit Integer 

17 

PM10 in µg/m

3

 (x10). 

Measurement averaged over 60 s and updated every 10 s. 

16-bit Integer 

18 

PM1.0 in N° of particles/ml. 

Measurement averaged over 15 min and updated every mi-
nute. 

16-bit Integer 

19 

PM2.5 in N° of particles/ml. 

Measurement averaged over 15 min and updated every mi-
nute. 

16-bit Integer 

20 

PM10 in N° of particles/ml. 

Measurement averaged over 15 min and updated every mi-
nute. 

16-bit Integer 

21 

PM1.0 in µg/m

3

 (x10). 

Measurement averaged over 15 min and updated every mi-
nute. 

16-bit Integer 

22 

PM2.5 in µg/m

3

 (x10). 

Measurement averaged over 15 min and updated every mi-
nute. 

16-bit Integer 

23 

PM10 in µg/m

3

 (x10). 

Measurement averaged over 15 min and updated every mi-
nute. 

16-bit Integer 

26 

PM measurement error: 0=no, 1=yes. 

Intero 16 bit 

28 

CO

2

 in ppm. 

Intero 16 bit 

33 

Atmospheric pressure in Pa 

(*) 

Internal sensor for CO

2

 measurement compensation 

Intero 32 bit 

35 

Atmospheric pressure in hPa (x10) 

Internal sensor for CO

2

 measurement compensation

 

Intero 16 bit 

37 

Power supply voltage in Volt (x10). 

16-bit Integer 

38 

Internal board temperature (x10). 

16-bit Integer 

40 

Instrument firmware revision. The most significant byte in-
dicates the major revision; the less significant byte indi-
cates the minor revision.

 

16-bit Integer 

41 

Number of MODBUS communication error. 

16-bit Integer 

(*) 

The measure is a 32-bit integer value.  Two  consecutive  registers (33 and 34) must be ac-

Summary of Contents for PMBsense-A

























Reviews: